Second hand
Label
-17%
Brand: PICA
Stock: In Stock
Pica BIG Ink Smart-Use Marker XL, Blue - 170/41
Pica BIG Ink 170/41 is a permanent marker with a deep hole function in blue. The manufacturer calls it the Smart-Use Marker XL - a combination of a deep hole marker and a permanent marker in one tool. Its thick tip allows both bold and precise marking on all smooth materials, while the extra-long tip reaches hard-to-reach places.
2-4 mm tip and the Twist&Revive system
The line width is 2-4 mm and the marker is 160 mm long. The special tip is soft and sturdy at the same time, which according to Pica gives it a unique writing feel. The double writing tip uses the Twist&Revive system: it can be twisted and reinserted, so the marker quickly revives and lasts longer.
XL ink reservoir and side holster
The XL ink reservoir gives a longer writing time. The marker sits in a side holster, so it is always at hand, and the manufacturer also lists one-hand operation. Pica advises always closing the marker after use to prevent it from drying out.
Ink
The red, blue and black variants use a permanent alcohol-based ink which, according to the manufacturer, is immediately water- and abrasion-resistant. This page is for the blue marker 170/41. For refilling, Pica sells the Ink Refill Set separately in black, blue and red - a glass bottle with 25 ml of ink and a pipette for precise dosing, enough for 15 fillings and more.
BIG Ink or Pica Ink
Pica's Innovative Line includes two ink markers for deep holes. Pica Ink is a deep hole marker with a 1.5 mm tip, while the manufacturer describes BIG Ink as a combination of a deep hole marker and a permanent marker - with a thicker 2-4 mm tip for bolder lines. The Ink Refill Set is shared by both markers.
Surfaces and colours
BIG Ink is intended for all smooth and dry surfaces. The manufacturer lists tiles, glass, plastic, paper, metal, rubber, wood and brick. The range comes in four colours - red (170/40), blue (170/41), black (170/46) and white (170/52) - and blister packs in the same colours are available for retail.
Technical specifications
ManufacturerPica-Marker (PICA)
Article170/41
EAN4260056158018
RangePica BIG Ink Smart-Use Marker XL
TypePermanent marker with deep hole function
ColourBlue
Line width2-4 mm
Marker length160 mm
InkPermanent, alcohol-based
ResistanceWater- and abrasion-resistant immediately
FeaturesExtra-long tip, Twist&Revive double tip, XL ink reservoir, side holster, one-hand operation
SurfacesSmooth and dry: tiles, glass, plastic, paper, metal, rubber, wood, brick
Questions and Answers
What is the deep hole function for?
The extra-long tip of the BIG Ink marks hard-to-reach places that an ordinary marker cannot reach. The manufacturer describes it as a deep hole marker and a permanent marker in one tool.
How wide is the line?
The manufacturer states a line width of 2-4 mm. The thick tip allows both bold and precise markings.
What ink does the marker use?
A permanent alcohol-based ink. According to the manufacturer the marking is water- and abrasion-resistant immediately after application.
Can the marker be refilled?
Yes. Pica sells the Ink Refill Set separately in black, blue and red: a glass bottle with 25 ml of ink and a pipette, enough for 15 fillings and more.
What is Twist&Revive?
It is the marker's double writing tip. It can be twisted and reinserted, so the marker quickly revives and lasts longer.
Which surfaces does the marker write on?
The manufacturer recommends it for all smooth and dry surfaces: tiles, glass, plastic, paper, metal, rubber, wood and brick. To keep it from drying out, always close the marker after use.
Which colours does BIG Ink come in?
Four colours: red 170/40, blue 170/41, black 170/46 and white 170/52. This item is the blue variant 170/41.
..
-17%
8.60€ 10.37€
Ex Tax:7.17€
Second hand
Label
-17%
Brand: PICA
Stock: In Stock
Pica BIG Ink Smart-Use Marker XL, Red - 170/40
Pica BIG Ink 170/40 is a permanent marker with a deep hole function in red. The manufacturer calls it the Smart-Use Marker XL - a combination of a deep hole marker and a permanent marker in one tool. Its thick tip allows both bold and precise marking on all smooth materials, while the extra-long tip reaches hard-to-reach places.
2-4 mm tip and the Twist&Revive system
The line width is 2-4 mm and the marker is 160 mm long. The special tip is soft and sturdy at the same time, which according to Pica gives it a unique writing feel. The double writing tip uses the Twist&Revive system: it can be twisted and reinserted, so the marker quickly revives and lasts longer.
XL ink reservoir and side holster
The XL ink reservoir gives a longer writing time. The marker sits in a side holster, so it is always at hand, and the manufacturer also lists one-hand operation. Pica advises always closing the marker after use to prevent it from drying out.
Ink
The red, blue and black variants use a permanent alcohol-based ink which, according to the manufacturer, is immediately water- and abrasion-resistant. This page is for the red marker 170/40. For refilling, Pica sells the Ink Refill Set separately in black, blue and red - a glass bottle with 25 ml of ink and a pipette for precise dosing, enough for 15 fillings and more.
BIG Ink or Pica Ink
Pica's Innovative Line includes two ink markers for deep holes. Pica Ink is a deep hole marker with a 1.5 mm tip, while the manufacturer describes BIG Ink as a combination of a deep hole marker and a permanent marker - with a thicker 2-4 mm tip for bolder lines. The Ink Refill Set is shared by both markers.
Surfaces and colours
BIG Ink is intended for all smooth and dry surfaces. The manufacturer lists tiles, glass, plastic, paper, metal, rubber, wood and brick. The range comes in four colours - red (170/40), blue (170/41), black (170/46) and white (170/52) - and blister packs in the same colours are available for retail.
Technical specifications
ManufacturerPica-Marker (PICA)
Article170/40
EAN4260056158001
RangePica BIG Ink Smart-Use Marker XL
TypePermanent marker with deep hole function
ColourRed
Line width2-4 mm
Marker length160 mm
InkPermanent, alcohol-based
ResistanceWater- and abrasion-resistant immediately
FeaturesExtra-long tip, Twist&Revive double tip, XL ink reservoir, side holster, one-hand operation
SurfacesSmooth and dry: tiles, glass, plastic, paper, metal, rubber, wood, brick
Questions and Answers
What is the deep hole function for?
The extra-long tip of the BIG Ink marks hard-to-reach places that an ordinary marker cannot reach. The manufacturer describes it as a deep hole marker and a permanent marker in one tool.
How wide is the line?
The manufacturer states a line width of 2-4 mm. The thick tip allows both bold and precise markings.
What ink does the marker use?
A permanent alcohol-based ink. According to the manufacturer the marking is water- and abrasion-resistant immediately after application.
Can the marker be refilled?
Yes. Pica sells the Ink Refill Set separately in black, blue and red: a glass bottle with 25 ml of ink and a pipette, enough for 15 fillings and more.
What is Twist&Revive?
It is the marker's double writing tip. It can be twisted and reinserted, so the marker quickly revives and lasts longer.
Which surfaces does the marker write on?
The manufacturer recommends it for all smooth and dry surfaces: tiles, glass, plastic, paper, metal, rubber, wood and brick. To keep it from drying out, always close the marker after use.
Which colours does BIG Ink come in?
Four colours: red 170/40, blue 170/41, black 170/46 and white 170/52. This item is the red variant 170/40.
..
-17%
8.60€ 10.37€
Ex Tax:7.17€
Second hand
Label
-17%
Brand: PICA
Stock: In Stock
Pica BIG Ink Smart-Use Marker XL, White - 170/52
Pica BIG Ink 170/52 is a permanent marker with a deep hole function in white. The manufacturer calls it the Smart-Use Marker XL - a combination of a deep hole marker and a permanent marker in one tool. Its thick tip allows both bold and precise marking on all smooth materials, while the extra-long tip reaches hard-to-reach places.
2-4 mm tip and the Twist&Revive system
The line width is 2-4 mm and the marker is 160 mm long. The special tip is soft and sturdy at the same time, which according to Pica gives it a unique writing feel. The double writing tip uses the Twist&Revive system: it can be twisted and reinserted, so the marker quickly revives and lasts longer.
XL ink reservoir and side holster
The XL ink reservoir gives a longer writing time. The marker sits in a side holster, so it is always at hand, and the manufacturer also lists one-hand operation. Pica advises always closing the marker after use to prevent it from drying out.
Ink
The white variant 170/52 uses Instant White ink - a permanent water-based ink that, according to the manufacturer, becomes water- and smudge-proof after approx. 20 seconds. Pica points out that white works great on dark surfaces and that the marker is available in white for the first time. The manufacturer offers its Ink Refill Set in black, blue and red.
BIG Ink or Pica Ink
Pica's Innovative Line includes two ink markers for deep holes. Pica Ink is a deep hole marker with a 1.5 mm tip, while the manufacturer describes BIG Ink as a combination of a deep hole marker and a permanent marker - with a thicker 2-4 mm tip for bolder lines. The Ink Refill Set is shared by both markers.
Surfaces and colours
BIG Ink is intended for all smooth and dry surfaces. The manufacturer lists tiles, glass, plastic, paper, metal, rubber, wood and brick. The range comes in four colours - red (170/40), blue (170/41), black (170/46) and white (170/52) - and blister packs in the same colours are available for retail.
Technical specifications
ManufacturerPica-Marker (PICA)
Article170/52
EAN4260056158032
RangePica BIG Ink Smart-Use Marker XL
TypePermanent marker with deep hole function
ColourWhite
Line width2-4 mm
Marker length160 mm
InkInstant White - permanent, water-based
ResistanceWater- and smudge-proof after approx. 20 seconds
FeaturesExtra-long tip, Twist&Revive double tip, XL ink reservoir, side holster, one-hand operation
SurfacesSmooth and dry: tiles, glass, plastic, paper, metal, rubber, wood, brick
Questions and Answers
What is the deep hole function for?
The extra-long tip of the BIG Ink marks hard-to-reach places that an ordinary marker cannot reach. The manufacturer describes it as a deep hole marker and a permanent marker in one tool.
How wide is the line?
The manufacturer states a line width of 2-4 mm. The thick tip allows both bold and precise markings.
What ink does the white marker use?
The white BIG Ink 170/52 uses Instant White - a permanent water-based ink. According to the manufacturer the marking becomes water- and smudge-proof after approx. 20 seconds.
Is there a refill for the white marker?
Pica offers its Ink Refill Set in black, blue and red. The manufacturer's data does not list a white refill.
What is Twist&Revive?
It is the marker's double writing tip. It can be twisted and reinserted, so the marker quickly revives and lasts longer.
Which surfaces does the marker write on?
The manufacturer recommends it for all smooth and dry surfaces: tiles, glass, plastic, paper, metal, rubber, wood and brick. To keep it from drying out, always close the marker after use.
Which colours does BIG Ink come in?
Four colours: red 170/40, blue 170/41, black 170/46 and white 170/52. This item is the white variant 170/52.
..
-17%
8.60€ 10.37€
Ex Tax:7.17€
Second hand
Brand: PICA
Stock: In Stock
PICA deep hole marker 150/41/SB in blue, supplied as 1 pc. This marker is intended for marking in hard-to-reach areas where a deeper reach is needed. The verified product identification matches the exact article number 150/41/SB, making it suitable for buyers who need to reorder the same item or add a single marker to their toolkit. The product information confirms the blue version and single-piece packaging...
9.20€
Ex Tax:7.67€
Second hand
Label
-17%
Brand: PICA
Stock: In Stock
Pica-Ink Deep Hole Marker, black, 150/46
Pica-Ink 150/46 is a marker for deep and hard-to-reach holes with black ink. Length 152 mm, line width 2 mm. The ink is permanent and waterproof. Supplied as 1 piece.
The colour
This article is black - both the ink and the body of the marker. Across the Pica-Ink 150 range the barrel colour follows the ink colour, so the variant is identified on sight rather than by testing it on the material: 150/46 is black, 150/40 red, 150/41 blue.
The extended tip
The tip is stainless steel, extended and adjustable. That is the whole point of the tool: an ordinary marker will not enter a hole, and even where it does, the thick barrel covers the spot so you cannot see where you are writing. The thin metal tip passes through the hole and marks the bottom.
Where it is used
On fixing through a finished surface: marking the structure behind a drilled hole, marking inside deep recesses, in sections, behind cladding and inside boxes. It also serves for marking in wet or oily conditions, where an ordinary pencil leaves nothing.
Permanent and waterproof
The ink is permanent - it does not smear on contact and does not disappear in damp. Working outdoors or in a cellar, that is essential: a mark made before the rain has to be there after it.
2 mm line width
2 mm is the compromise between visibility and precision. A finer line is lost on a rough substrate - concrete, brick, sawn timber; a thicker one will not place a point with usable accuracy.
Ink or graphite
The Pica deep-hole range comes in two kinds, and the choice between them is not a matter of taste. Ink markers such as this one write on smooth, wet and oily surfaces - metal, plastic, glazed tile - where graphite simply slides. The graphite versions suit dry timber, concrete and plasterboard, where the mark later has to be rubbed or sanded away. Ink is permanent: on a surface that will be seen, it can still show through a thin coat of paint.
The metal tip
The tip is stainless steel rather than plastic or felt. The difference is in its life: a felt tip of that length crushes the first time it meets concrete, whereas the metal one keeps its shape.
Technical specifications
ManufacturerPica
Article number150/46
RangePica-Ink Deep Hole Marker
Ink colourblack
Line width2 mm
Length152 mm
TipExtended, adjustable, stainless steel
InkPermanent, waterproof
Quantity1 piece
EAN4260056150012
Questions and Answers
What colour is the marker?
Black - both the ink and the body. Across the Pica-Ink 150 range the barrel colour follows the ink colour, so the variant is known on sight.
What is the length?
152 mm, with a 2 mm line width.
Why is the tip extended?
An ordinary marker will not enter a hole, and even where it does the thick barrel covers the spot. The thin metal tip passes through and marks the bottom.
What is the tip made of?
Stainless steel, not plastic or felt. A felt tip of that length crushes the first time it meets concrete.
Does it survive damp?
Yes - the ink is permanent and waterproof. A mark made before the rain is there after it.
Why a 2 mm line?
The compromise between visibility and precision: finer is lost on concrete and sawn timber, thicker will not place an accurate point.
How many in the pack?
One.
..
-17%
8.50€ 10.20€
Ex Tax:7.08€
Second hand
Label
-17%
Brand: PICA
Stock: In Stock
Pica-Ink Deep Hole Marker, blue, 150/41
Pica-Ink 150/41 is a marker for deep and hard-to-reach holes with blue ink. Length 152 mm, line width 2 mm. The ink is permanent and waterproof. Supplied as 1 piece.
A note on the colour
The body of the marker is black with orange trim on every version in the range - the colour in the name refers to the ink, not the barrel. This article writes in blue.
The extended tip
The tip is stainless steel, extended and adjustable. That is the whole point of the tool: an ordinary marker will not enter a hole, and even where it does, the thick barrel covers the spot so you cannot see where you are writing. The thin metal tip passes through the hole and marks the bottom.
Where it is used
On fixing through a finished surface: marking the structure behind a drilled hole, marking inside deep recesses, in sections, behind cladding and inside boxes. It also serves for marking in wet or oily conditions, where an ordinary pencil leaves nothing.
Permanent and waterproof
The ink is permanent - it does not smear on contact and does not disappear in damp. Working outdoors or in a cellar, that is essential: a mark made before the rain has to be there after it.
2 mm line width
2 mm is the compromise between visibility and precision. A finer line is lost on a rough substrate - concrete, brick, sawn timber; a thicker one will not place a point with usable accuracy.
Ink or graphite
The Pica deep-hole range comes in two kinds, and the choice between them is not a matter of taste. Ink markers such as this one write on smooth, wet and oily surfaces - metal, plastic, glazed tile - where graphite simply slides. The graphite versions suit dry timber, concrete and plasterboard, where the mark later has to be rubbed or sanded away. Ink is permanent: on a surface that will be seen, it can still show through a thin coat of paint.
The metal tip
The tip is stainless steel rather than plastic or felt. The difference is in its life: a felt tip of that length crushes the first time it meets concrete, whereas the metal one keeps its shape.
Technical specifications
ManufacturerPica
Article number150/41
RangePica-Ink Deep Hole Marker
Ink colourblue
Line width2 mm
Length152 mm
TipExtended, adjustable, stainless steel
InkPermanent, waterproof
Quantity1 piece
EAN4260056150029
Questions and Answers
What colour is the marker?
It writes in blue. The body, however, is black with orange trim on every version - the colour in the name refers to the ink.
What is the length?
152 mm, with a 2 mm line width.
Why is the tip extended?
An ordinary marker will not enter a hole, and even where it does the thick barrel covers the spot. The thin metal tip passes through and marks the bottom.
What is the tip made of?
Stainless steel, not plastic or felt. A felt tip of that length crushes the first time it meets concrete.
Does it survive damp?
Yes - the ink is permanent and waterproof. A mark made before the rain is there after it.
Why a 2 mm line?
The compromise between visibility and precision: finer is lost on concrete and sawn timber, thicker will not place an accurate point.
How many in the pack?
One.
..
-17%
8.50€ 10.22€
Ex Tax:7.08€
Second hand
Label
-15%
Brand: PICA
Stock: In Stock
Pica-Ink Deep Hole Marker, red, 150/40
Pica-Ink 150/40 is a marker for deep and hard-to-reach holes with red ink. Length 152 mm, line width 2 mm. The ink is permanent and waterproof. Supplied as 1 piece.
The colour
This article is red - both the ink and the body of the marker. Across the Pica-Ink 150 range the barrel colour follows the ink colour, so the variant is identified on sight rather than by testing it on the material: 150/40 is red, 150/46 black, 150/41 blue.
The extended tip
The tip is stainless steel, extended and adjustable. That is the whole point of the tool: an ordinary marker will not enter a hole, and even where it does, the thick barrel covers the spot so you cannot see where you are writing. The thin metal tip passes through the hole and marks the bottom.
Where it is used
On fixing through a finished surface: marking the structure behind a drilled hole, marking inside deep recesses, in sections, behind cladding and inside boxes. It also serves for marking in wet or oily conditions, where an ordinary pencil leaves nothing.
Permanent and waterproof
The ink is permanent - it does not smear on contact and does not disappear in damp. Working outdoors or in a cellar, that is essential: a mark made before the rain has to be there after it.
2 mm line width
2 mm is the compromise between visibility and precision. A finer line is lost on a rough substrate - concrete, brick, sawn timber; a thicker one will not place a point with usable accuracy.
Ink or graphite
The Pica deep-hole range comes in two kinds, and the choice between them is not a matter of taste. Ink markers such as this one write on smooth, wet and oily surfaces - metal, plastic, glazed tile - where graphite simply slides. The graphite versions suit dry timber, concrete and plasterboard, where the mark later has to be rubbed or sanded away. Ink is permanent: on a surface that will be seen, it can still show through a thin coat of paint.
The metal tip
The tip is stainless steel rather than plastic or felt. The difference is in its life: a felt tip of that length crushes the first time it meets concrete, whereas the metal one keeps its shape.
Technical specifications
ManufacturerPica
Article number150/40
RangePica-Ink Deep Hole Marker
Ink colourred
Line width2 mm
Length152 mm
TipExtended, adjustable, stainless steel
InkPermanent, waterproof
Quantity1 piece
EAN4260056150104
Questions and Answers
What colour is the marker?
Red - both the ink and the body. Across the Pica-Ink 150 range the barrel colour follows the ink colour, so the variant is known on sight.
What is the length?
152 mm, with a 2 mm line width.
Why is the tip extended?
An ordinary marker will not enter a hole, and even where it does the thick barrel covers the spot. The thin metal tip passes through and marks the bottom.
What is the tip made of?
Stainless steel, not plastic or felt. A felt tip of that length crushes the first time it meets concrete.
Does it survive damp?
Yes - the ink is permanent and waterproof. A mark made before the rain is there after it.
Why a 2 mm line?
The compromise between visibility and precision: finer is lost on concrete and sawn timber, thicker will not place an accurate point.
How many in the pack?
One.
..
-15%
8.50€ 10.03€
Ex Tax:7.08€
Second hand
Brand: PICA
Stock: In Stock
Pica-Ink Deep Hole Marker, Red, 150/40/SB
Pica-Ink 150/40 is a marker for hard-to-reach places, with red ink, a length of 152 mm and a 2 mm line. The ink is permanent and waterproof. EAN 4260056150104. The SB suffix denotes blister packaging.
The extended tip
The tip is extended, in stainless steel, and adjustable. That is the whole point of the range: the marker reaches into a drilled hole, a narrow gap or behind a section where an ordinary marker fouls on the edge and never reaches the bottom. For marking hole depth or a point behind an obstruction there is effectively no alternative.
Permanent and waterproof
The ink does not rub off and does not wash away. That is the difference from the graphite Pica-Dry range, whose mark can be corrected. Here the marking is final - an advantage where it must survive rain, dust and handling, and a drawback for setting out lines that later get in the way.
Why red
On the Pica-Ink range the body colour follows the ink colour, so the variant is recognisable on sight without opening it. Red reads well on light and metallic surfaces. The range also offers black (150/46) and blue (150/41) for other substrates.
Loose or blister
The same marker exists under two numbers: 150/40 loose and 150/40/SB on a retail blister. The tool is identical; only the packaging differs. Check the number when ordering, because the names are practically the same.
What it writes on
PICA's ink markers grip metal, plastic, wood and stone, including smooth and lightly oiled surfaces. That makes them an installation tool rather than an office marker.
Storage
Keep the marker tightly capped and preferably horizontal. A fine metal tip dries out faster than a broad felt one, and once blocked it is hard to recover - the usual reason such a marker stops writing long before the ink runs out.
Technical specifications
ManufacturerPICA
Article150/40/SB
RangePica-Ink
TypeDeep hole marker
Ink colourRed
Line width2 mm
Length152 mm
Pieces in pack1
TipExtended, adjustable, stainless steel
InkPermanent, waterproof
PackagingBlister (SB)
EAN4260056150104
Questions and Answers
What is the extended tip for?
It reaches into a drilled hole, gap or behind a section where an ordinary marker cannot.
What colour is it?
Red ink. On Pica-Ink the body colour follows the ink colour.
Does the mark rub off?
No. The ink is permanent and waterproof. For a correctable mark use the graphite Pica-Dry range.
How does it differ from article 150/40?
Not at all in the tool - 150/40 is loose, 150/40/SB is on a blister.
How many markers are in the pack?
One.
What will it write on?
Metal, plastic, wood and stone, including smooth surfaces.
Why does it stop writing?
Usually a dried tip - a fine metal tip dries quickly if the cap is not closed tightly.
..
9.20€
Ex Tax:7.67€
Second hand
New
Label
-11%
Brand: Bosch
Stock: In Stock
Bosch Deep Hole Marker Pencil, 1 600 A03 B64
The Bosch 1 600 A03 B64 mechanical pencil is made for marking where an ordinary pencil cannot reach: inside a finished hole, behind a pipe, in a narrow gap. The long tip, on a 5.7 mm shank, passes through a hole in a wall or in formwork and leaves a clear mark at the bottom of it. The pencil is 151 mm long overall.
Body and lead
The body is stainless steel - resistant to bending and to the damp that is normal on a building site. The lead is 2.8 mm in diameter with HB hardness, the general-purpose grade that writes dark enough on timber and plasterboard without snapping under pressure on a rough surface.
Integrated sharpener
A sharpener is built into the cap. On a tool for this job it is essential: a mark in a deep hole is only useful if the tip is sharp, and a 2.8 mm lead blunts quickly on concrete and render. The sharpener travels with the pencil, so sharpening needs no second tool.
Replacement leads
Bosch supplies replacement leads for this pencil in two versions - HB under part number 1 600 A03 AL4 and Multicolor (2 HB, 2 red, 2 yellow) under 1 600 A03 AL5. Both are 2.8 mm in diameter and 120 mm long.
Applications
Carrying a centre line through an existing hole, marking depth in a blind hole, marking behind pipes and cables, scribing in corners and gaps - the everyday tasks of an electrician, a plumber, a drylining fitter and a carpenter.Technical specifications
BrandBosch Professional
Part number1600 A03 B64
EAN4059952741253
TypeDeep hole marker pencil
Lead diameter2.8 mm
Lead hardnessHB
Shank diameter5.7 mm
Length151 mm
Body materialStainless steel
SharpenerIntegrated
Replacement leads1 600 A03 AL4 (HB), 1 600 A03 AL5 (Multicolor)
Pack quantity1 pc
PackagingCardboard packaging, hanger, with Euro hole
Questions and Answers
What is a deep hole marker pencil for?
The long, thin tip enters a drilled hole or a narrow gap and leaves a mark where an ordinary pencil cannot reach. It is typically used to carry a centre line through a wall and to mark depth in a blind hole.
What lead does it take?
A 2.8 mm lead. Bosch supplies replacements under 1 600 A03 AL4 (HB, 6 per pack) and 1 600 A03 AL5 (Multicolor: 2 HB, 2 red, 2 yellow, 6 per pack), both 120 mm long.
Does it have a sharpener?
Yes, the sharpener is built into the cap of the pencil and is sized for the 2.8 mm lead.
What is the body made of?
Stainless steel. That is an advantage on site - the body does not bend when carried in a work trouser pocket and does not rust in damp conditions.
What is the overall length and shank diameter?
151 mm overall, with a 5.7 mm shank diameter. That determines the size of hole the tip can pass through.
What does HB hardness mean, and does it suit every material?
HB is the middle, general-purpose grade. It writes well on timber, plasterboard and paper. Very smooth or wet surfaces need special lead compounds, which Bosch does not offer for this pencil.
Is it suitable for marking metal?
Graphite does leave a mark on metal, but on an oily or mirror-smooth surface it rubs off easily. For durable scribing on metal use a scriber or a marking lead with a different compound.
..
-11%
8.90€ 10.00€
Ex Tax:7.42€
Second hand
Label
-15%
Brand: PICA
Stock: In Stock
Pica Powder Deep Hole Spray Marker, up to 25 cm, Blister, 2020/SB
Pica Powder 2020/SB is a spray marker for point marking in deep holes - down to 25 cm (10 inches). One cartridge gives 1,500 marks. The marker is refillable and works without propellant. It is supplied in a blister pack with a euro hanging hole - which is what the SB suffix means.
Powder, not ink
This marker does not write - it shoots powder. A thin metal tube goes into the hole, you press, and a puff of coloured powder leaves the tip and lands as a dot at the bottom. That is where the reach comes from: an ink marker depends on the length of its tip, whereas powder travels as far as the tube does.
No propellant
The pack states it plainly: Ohne Treibgas / Without aerosol. The marker is not an aerosol: there is no pressurised gas, which brings three consequences - it can be carried and stored without dangerous-goods restrictions, it is unaffected by temperature, and it does not lose pressure standing unused.
25 centimetres
25 cm is a depth no pencil or ink marker reaches. The typical job is marking the structure behind a drilled hole - through insulation, cladding, a suspended ceiling or a cavity between two skins. At those thicknesses the alternative is opening the cladding up to see where to drill.
1,500 marks
One cartridge lasts 1,500 shots. For scale, that is the order of a whole job - the marker does not run out halfway through. When the powder is spent, the cartridge is replaced, not the whole marker.
The clip
The body carries a pocket clip. On a tool used several times an hour and put down in between, that is practical: the marker rides on the trouser pocket rather than in a bag at the other end of the site.
The blister
The SB suffix in the article number means a self-service blister pack - card with a clear shell and a euro hole for hanging. The product is the same as the loose 2020 version; only the packaging differs.
Technical specifications
ManufacturerPica
Article number2020/SB
RangePica Powder
TypeDeep hole spray marker
Marking depthup to 25 cm (10 inches)
Marks1,500 per cartridge
CartridgeRefillable
PropellantNone - not an aerosol
PackagingBlister with euro hole
OriginGermany
Questions and Answers
How deep does it mark?
Down to 25 cm (10 inches) - a depth neither pencil nor ink marker reaches.
How does it work?
It does not write but shoots powder. A thin metal tube enters the hole and a puff of coloured powder leaves the tip, landing as a dot at the bottom.
Is it an aerosol?
No. The pack states Without aerosol - there is no pressurised gas, so no restrictions on carriage or storage.
How many marks does it make?
1,500 per cartridge. When the powder is spent, the cartridge is replaced, not the whole marker.
How does it differ from article 2020?
Only the packaging. The SB suffix means a self-service blister with a euro hole; the product inside is the same.
What is it for?
Marking the structure behind a drilled hole - through insulation, cladding, a suspended ceiling or a cavity between two skins.
Does it have a clip?
Yes - a pocket clip on the body, for a tool used several times an hour.
..
-15%
14.80€ 17.38€
Ex Tax:12.33€
Second hand
Label
-30%
Brand: Dewalt
Stock: In Stock
DeWALT 2-771 Can Filling PumpFeatures:
The DeWALT 2-771 Box Filling Pump is made of high-grade aluminum with a hard anodized finish, ensuring maximum durability. It features a longer body and a longer handle compared to competing models, allowing for easy and convenient loading of the mixture. The pump is easy to assemble and disassemble, making cleaning a breeze. It is equipped with a built-in switch for added convenience and includes an extra-long DEWALT box-filling adapter (2-715).
Technical Specifications:Made of premium aluminum with a hard anodized finishLonger body and longer handle compared to competing modelsEasy to assemble and disassembleIncluded:DEWALT / 2-715 / long box-filling adapter..
-30%
399.00€ 572.00€
Ex Tax:332.50€
Second hand
Label
-25%
Brand: Dewalt
Stock: In Stock
-25%
393.00€ 526.00€
Ex Tax:327.50€
Second hand
Label
-37%
Brand: Dewalt
Stock: In Stock
DeWALT DXTT-2-764 Flat Putty KnifeFeatures:
The DeWALT DXTT-2-764 putty knife is constructed with an anodized aluminum body and stainless steel blades for high durability and strength. The flexible holder for the brass blades allows for precise application of the exact amount of joint compound, ensuring ease and comfort of use
. The lid itself is spring-loaded, ensuring easy opening and closing for added convenience during cleaning. The box applies an even, consistent layer of joint compound to joints on walls and ceilings, making all edges and corners perfect.
https://youtu.be/Rtqmrlh61VY..
-37%
336.82€ 535.89€
Ex Tax:280.68€
Second hand
Label
-36%
Brand: Dewalt
Stock: In Stock
DeWALT DXTT-2-765 Flat Putty KnifeFeatures:
The DeWALT DXTT-2-765 putty knife is constructed with an anodized aluminum body and stainless steel blades for high durability and strength. The flexible holder for the brass blades allows for precise application of the exact amount of joint compound, ensuring ease and comfort of use
. The lid itself is spring-loaded, ensuring easy opening and closing for added convenience during cleaning. The box applies an even, consistent layer of joint compound to joints on walls and ceilings, making all edges and corners perfect.
https://youtu.be/Rtqmrlh61VY..
-36%
347.68€ 546.06€
Ex Tax:289.73€
Second hand
Label
-35%
Brand: Dewalt
Stock: In Stock
DeWALT DXTT-2-767 Flat Putty KnifeFeatures:
The DeWALT DXTT-2-767 putty knife is constructed with an anodized aluminum body and stainless steel blades for high durability and strength. The flexible holder for the brass blades allows for precise application of the exact amount of joint compound, ensuring ease and comfort of use
. The lid itself is spring-loaded, ensuring easy opening and closing for added convenience during cleaning. The box applies an even, consistent layer of joint compound to joints on walls and ceilings, making all edges and corners perfect.
https://youtu.be/Rtqmrlh61VY..
-35%
391.78€ 600.26€
Ex Tax:326.48€
Second hand
Label
-14%
Stock: In Stock
Milwaukee 4932352332 Holesaw Drilling GuideThe Milwaukee Holesaw Drilling Guide is a specialized drilling guide designed for use with diamond drill bits and hole saws ranging from 19 to 68 mm. It ensures more precise starting and more stable tool guidance when drilling into hard and brittle building materials, including ceramic tiles.Application and ConvenienceThe accessory is suitable for clean and controlled hole drilling during installation work, such as routing pipes, cables, and other installations. The guide helps prevent the drill bit from slipping on smooth surfaces and reduces the risk of damaging the surface finish.Practical featuresThe model is designed to operate with a continuous water jet during drilling, which aids cooling, dust removal, and extends the life of diamond consumables. According to the available information, it attaches via vacuum to suitable surfaces, and the set includes 1 guide. The item number is 4932352332 and the EAN is 4002395369911.A suitable choice for precision work on tiles and other similar materials, where it is important that the hole be cut accurately and without unnecessary damage...
-14%
46.50€ 54.00€
Ex Tax:38.75€
Second hand
Brand: Stanley
Stock: In Stock
Two cutting blades allow the user to cut both sides of the material at the same time • Dual-material handle for comfort and protection • Adjustable cutting depth • Replacement blades available • Specialized cutter for drywall with a cutting depth of 9.5 to 15 mm..
28.12€
Ex Tax:23.43€
Second hand
Brand: PICA
Stock: In Stock
Fine Permanent Pen Pica Classic 533 Permanent Pen, Black - 533/46
Pica Classic 533/46 is a Permanent Pen with a fine (F) 0.7 mm tip and black ink. The manufacturer designs it for precise markings that dry instantly. The ink is permanent and alcohol-based and, according to Pica, immediately abrasion and water resistant. The pen marks permanently on almost all surfaces.
Fine or medium tip
The Pica Classic 533/534 series comes with two tip sizes: fine (F) 0.7 mm for precise marking - model 533 - and medium (M) 1 mm for more visible marking - model 534. This page is for the fine 533 pen in black. The barrel is printed "Permanent Pen - Fine - 0,7 mm", and the cap has a clip.
Ink properties
In its product sheets Pica states that the ink is fast drying, water resistant and indelible, and that the pen is free of xylene and toluene. This makes it suitable for labels and marks that must remain legible after contact with water.
Surfaces and trades
The manufacturer lists metal, wood, plastic, glass, paper, tiles and brick as suitable surfaces. In the earlier product sheet Pica recommends the pen for electrical engineering, glaziers, locksmiths, mechanics, sanitary engineering, tilers and woodwork.
Packaging and variants
Pica supplies the 533/46 pens in trade packs of 10. For self-service the manufacturer offers the same pen in a blister as item 533/46/SB, and for shops a display for the Classic line markers (item 66520). The industrial marker group of Pica Classic also includes the 524 paint marker, the 520/521 permanent marker and the 528 XXL permanent marker.
Technical specifications
ManufacturerPica-Marker (PICA)
Item number533/46
EAN4260056155048
SeriesPica Classic 533/534 Permanent Pen
TypeFine-tip permanent pen
ColourBlack
TipFine (F), 0.7 mm
InkPermanent, alcohol-based
PropertiesFast drying, immediately abrasion and water resistant, indelible
CompositionFree of xylene and toluene
SurfacesMetal, wood, plastic, glass, paper, tiles, brick
Manufacturer's packagingPacks of 10; blister version 533/46/SB
Questions and Answers
What kind of ink does it use?
Pica specifies a permanent alcohol-based ink. According to the manufacturer it is immediately abrasion and water resistant.
How wide is the line?
The 533 pen has a fine (F) 0.7 mm tip for precise marking. For more visible lines the manufacturer offers model 534 with a medium 1 mm tip.
Does water remove the marking?
No. The manufacturer describes the ink as water resistant and indelible, immediately resistant to abrasion and water.
Which surfaces does the pen mark?
Pica lists metal, wood, plastic, glass, paper, tiles and brick. The manufacturer describes the pen as suitable for permanent marking on almost all surfaces.
Does it contain xylene or toluene?
No. The manufacturer states that Pica Classic 533/534 pens are free of xylene and toluene.
What is the difference between 533/46 and 533/46/SB?
The pen is the same - Pica Classic 533, black, with a fine 0.7 mm tip. Item 533/46/SB is the blister version for self-service.
Which trades is it intended for?
In its product sheet Pica recommends it for electrical engineering, glaziers, locksmiths, mechanics, sanitary engineering, tilers and woodwork.
..
1.98€
Ex Tax:1.65€
Second hand
Brand: PICA
Stock: In Stock
Pica Classic 590 PRO Forester & Signing Chalk, Blue - 590/41
Pica Classic 590/41 is a forester and signing chalk from the Classic 590 PRO range in blue. The manufacturer describes the chalks of this line as premium-quality products made from the best raw materials for professional applications. The chalk is hexagonal, 12 mm in diameter and 120 mm long, and is designed for permanent marking on dry and wet wood.
Rich colour and high breaking strength
Thanks to its high pigmentation the chalk leaves a rich, clearly visible mark. Pica also states a high breaking strength. The chalk is wrapped in a paper label that keeps fingers clean while working – the manufacturer lists it as one of the advantages of the range.
Lumber – dry and wet
In its earlier product sheet Pica calls the 590 PRO a "lumber and industrial marking crayon" and describes it as ideal for permanent marking on dry and wet lumber. Besides wood, according to the manufacturer the chalk is also suitable for metal, stone, concrete and plastic. Its list of suitable surfaces reads brick, stone, concrete, wood, wet wood, rubber, metal, plastic and paper.
Chalk holder
For this chalk the manufacturer recommends its Pica Classic 588 holder. Pica describes it as a holder with a high-quality push mechanism made to match the brand's chalks. The holder is sold separately.
Colours and packaging
The Classic 590 PRO range comes in six colours: green (590/36), red (590/40), blue (590/41), yellow (590/44), black (590/46) and white (590/52). This page is for the blue chalk 590/41. The manufacturer packs the chalks 12 to a hangable cardboard box. In the same group Pica also offers the Classic 591 ECO range – also hexagonal, 11 mm in diameter and 110 mm long.
Other chalks in the Classic Line
The forester chalk belongs to the chalk group of the Pica Classic line. In it the manufacturer also offers soapstone chalk (571), blackboard chalk (581) and luminescent chalk (592) – each for a different kind of marking.
Technical specifications
ManufacturerPica-Marker (PICA)
Article590/41
EAN4260056153068
RangePica Classic 590 PRO
TypeForester and signing chalk
ColourBlue
ShapeHexagonal
Diameter12 mm
Length120 mm
FeaturesHigh pigmentation, high breaking strength, wrap-around paper label
SurfacesBrick, stone, concrete, wood, wet wood, rubber, metal, plastic, paper
Manufacturer's packagingHangable cardboard box of 12 chalks
Recommended accessoryPica Classic 588 chalk holder
Questions and Answers
Which materials is the chalk suitable for?
The manufacturer recommends it for permanent marking on dry and wet wood. It is also suitable for metal, stone, concrete, brick, plastic, rubber and paper.
Does the chalk mark wet wood?
Yes. Pica explicitly lists wet wood among the suitable surfaces and describes the 590 PRO range as ideal for permanent marking on dry and wet lumber.
What are the dimensions of the chalk?
The chalk is hexagonal, 12 mm in diameter and 120 mm long. The wrap-around paper label keeps fingers clean while working.
How does the 590 PRO range differ from 591 ECO?
Both ranges are hexagonal, but 590 PRO is 12 mm in diameter and 120 mm long, while 591 ECO is 11 mm in diameter and 110 mm long. The manufacturer presents them as two versions of its forester and signing chalk.
Is there a matching chalk holder?
Yes, Pica recommends its Classic 588 holder with a push mechanism, made to match the brand's chalks. The holder is sold separately.
How strong is the chalk?
The manufacturer states a high breaking strength. The high pigmentation gives the marking a rich, clearly visible colour.
Which colours does the range come in?
Six colours: green 590/36, red 590/40, blue 590/41, yellow 590/44, black 590/46 and white 590/52. This item is the blue chalk 590/41.
..
0.99€
Ex Tax:0.83€
Second hand
Brand: PICA
Stock: In Stock
Pica Classic 590 PRO Forester & Signing Chalk, Red - 590/40
Pica Classic 590/40 is a forester and signing chalk from the Classic 590 PRO range in red. The manufacturer describes the chalks of this line as premium-quality products made from the best raw materials for professional applications. The chalk is hexagonal, 12 mm in diameter and 120 mm long, and is designed for permanent marking on dry and wet wood.
Rich colour and high breaking strength
Thanks to its high pigmentation the chalk leaves a rich, clearly visible mark. Pica also states a high breaking strength. The chalk is wrapped in a paper label that keeps fingers clean while working - the manufacturer lists it as one of the advantages of the range.
Lumber - dry and wet
In its earlier product sheet Pica calls the 590 PRO a "lumber and industrial marking crayon" and describes it as ideal for permanent marking on dry and wet lumber. Besides wood, according to the manufacturer the chalk is also suitable for metal, stone, concrete and plastic. Its list of suitable surfaces reads brick, stone, concrete, wood, wet wood, rubber, metal, plastic and paper.
Chalk holder
For this chalk the manufacturer recommends its Pica Classic 588 holder. Pica describes it as a holder with a high-quality push mechanism made to match the brand's chalks. The holder is sold separately.
Colours and packaging
The Classic 590 PRO range comes in six colours: green (590/36), red (590/40), blue (590/41), yellow (590/44), black (590/46) and white (590/52). This page is for the red chalk 590/40. The manufacturer packs the chalks 12 to a hangable cardboard box. In the same group Pica also offers the Classic 591 ECO range - also hexagonal, 11 mm in diameter and 110 mm long.
Other chalks in the Classic Line
The forester chalk belongs to the chalk group of the Pica Classic line. In it the manufacturer also offers soapstone chalk (571), blackboard chalk (581) and luminescent chalk (592) - each for a different kind of marking.
Technical specifications
ManufacturerPica-Marker (PICA)
Article590/40
EAN4260056153051
RangePica Classic 590 PRO
TypeForester and signing chalk
ColourRed
ShapeHexagonal
Diameter12 mm
Length120 mm
FeaturesHigh pigmentation, high breaking strength, wrap-around paper label
SurfacesBrick, stone, concrete, wood, wet wood, rubber, metal, plastic, paper
Manufacturer's packagingHangable cardboard box of 12 chalks
Recommended accessoryPica Classic 588 chalk holder
Questions and Answers
Which materials is the chalk suitable for?
The manufacturer recommends it for permanent marking on dry and wet wood. It is also suitable for metal, stone, concrete, brick, plastic, rubber and paper.
Does the chalk mark wet wood?
Yes. Pica explicitly lists wet wood among the suitable surfaces and describes the 590 PRO range as ideal for permanent marking on dry and wet lumber.
What are the dimensions of the chalk?
The chalk is hexagonal, 12 mm in diameter and 120 mm long. The wrap-around paper label keeps fingers clean while working.
How does the 590 PRO range differ from 591 ECO?
Both ranges are hexagonal, but 590 PRO is 12 mm in diameter and 120 mm long, while 591 ECO is 11 mm in diameter and 110 mm long. The manufacturer presents them as two versions of its forester and signing chalk.
Is there a matching chalk holder?
Yes, Pica recommends its Classic 588 holder with a push mechanism, made to match the brand's chalks. The holder is sold separately.
How strong is the chalk?
The manufacturer states a high breaking strength. The high pigmentation gives the marking a rich, clearly visible colour.
Which colours does the range come in?
Six colours: green 590/36, red 590/40, blue 590/41, yellow 590/44, black 590/46 and white 590/52. This item is the red chalk 590/40.
..
0.99€
Ex Tax:0.83€