DeWalt Fargo Black Safety Footwear, Size 46 (UK 12), DWF50233-101-12 DeWalt Fargo Black (order number DWF50233-101-12) is protective work footwear with a low cut profile in EU size 46, corresponding to UK 12. It is classified SB SRA HRO FO to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap and no midsole plate. Leaving out the plate means more flexibility and less weight, but also that these are not intended for ground with nails and protruding steel - such conditions call for a class carrying a P or S mark. Upper and waterproofing The upper is lightweight synthetic upper with a reinforced toe area. The synthetic upper is considerably lighter than leather and dries faster, but offers no waterproofing - these are for dry conditions and indoor work. Sole The sole is an Phylon/rubber outsole with heat resistance. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 12 is EU 46. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Fargo Black Order numberDWF50233-101-12 SizeEU 46 (UK 12) ClassificationSB SRA HRO FO StandardEN ISO 20345 Profilelow cut Toe capsteel toe cap Underfoot protectionno midsole plate Upperlightweight synthetic upper with a reinforced toe area SolePhylon/rubber outsole with heat resistance FasteningConventional laces WaterproofNo Questions and Answers What size is this footwear? Order number DWF50233-101-12 corresponds to UK size 12, that is EU 46. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the SB SRA HRO FO classification mean? SB is the base level - a protective toe cap and nothing more. SRA is tested slip resistance on ceramic tile with detergent, HRO is the sole's resistance to contact heat, and FO resistance to fuel and oil. Is there metal in the construction? Yes - a steel toe cap. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? No. The synthetic upper is not waterproof and has no membrane. These are intended for dry conditions and indoor work; wet environments call for an S3 class model with a membrane. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? The synthetic upper cleans with a damp cloth and mild detergent. Dry at room temperature away from a radiator - direct heat deforms the Phylon sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DEWALT DWF50233-101-7 Steel-Toe Work BootsDescription: DEWALT Fargo Black work shoes are the perfect combination of modern design and reliable protection. The upper is made of lightweight synthetic material that ensures durability and longevity. With a padded tongue and collar, they provide extra comfort around the ankle. The included comfortable polyurethane insole ensures comfort and better shock absorption during long work hours. The shoe's outsole, made from a combination of phylon and rubber, offers excellent traction and stability on various work surfaces. For added safety, the shoes feature a steel toe cap that protects the toes from potential injuries. They are suitable for various work environments and are ideal for workers who value style and protection in one. Technical specifications:Size: 41Type: low-cutProtection class: SB, SRAMaterial: synthetic material and textileToe cap: metal (200J)Plate in the sole: noInsole length: 27.5 cmInsole: PUOutsole: phylon/rubberTraction: slip-resistant..

DeWalt Millington Brown Rigger Boots, Size 41 (UK 7), DWF50202-104-7 DeWalt Millington Brown (order number DWF50202-104-7) is a rigger-style safety boot in EU size 41, which corresponds to UK 7. It is classified S3 WR HRO SRA to EN ISO 20345. A rigger boot has no laces at all - it is pulled on and off by the two loops at the top of the shaft, which matters on sites where boots come off and go back on several times a day. Fully non-metallic construction The Millington is 100% non-metallic: the toe cap is composite and the anti-penetration midsole is non-metallic as well. That has three practical consequences. The boot is noticeably lighter than its steel equivalent at the same protection rating. It creates no cold bridge - a steel toe cap conducts outside cold straight to your toes, and in winter you feel that within the first hour. And it will not set off metal detectors, which matters at airports, in plants that screen for metal, and around sensitive instrumentation. Upper and waterproofing The upper is brown nubuck leather with a tall shaft that covers the ankle and the lower calf. Inside sits a waterproof breathable lining. The membrane works in both directions - it keeps water out while letting perspiration vapour escape - and this is exactly what separates a genuinely waterproof boot from a merely treated one, where your foot ends up damp from its own moisture after a few hours. An anti-scuff toe guard sits over the toe area and takes the abrasion from kneeling and from pushing material with the front of the boot, which is where nubuck otherwise wears through first. Outsole and heat resistance The outsole is dual-density PU/rubber. The polyurethane midlayer does the cushioning while the rubber outer layer absorbs the wear and delivers the grip. The HRO marking in the classification means tested resistance to contact heat up to 300 °C - relevant around hot asphalt, welding bays and roofing membranes. The tread is deeply cleated with a defined heel. Rigger versus laced boot Choosing between the two is not a matter of taste. A rigger goes on in seconds and has no laces to snag or come undone, which is why it is the default in the oil industry, on scaffolding, in agriculture and anywhere people step in and out repeatedly. The trade-off is that the fit cannot be adjusted: the boot has to suit your calf and your instep as it comes. If you have a high instep or a fuller calf, a laced model gives you more room to work with. Choosing your size The order number ends with the UK size and the European size is that number plus 34 - so UK 7 is EU 41. Trying rigger boots on matters more than with a laced model, because there is no way to tighten the fit afterwards. Try them in the afternoon, when your foot has swollen slightly, and with the socks you actually work in: a composite toe cap does not give, and pressure across the toes will not break in with wear. Who they are for The Millington is aimed at construction and installation crews, plant and machinery operators, warehouse and transport work, utilities and agriculture - anywhere you stand and walk all day, the ground is wet, and a dropped object or a nail underfoot is a real risk. Safety footwear remains the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries measured in months of recovery. Technical specifications ModelDeWalt Millington Brown Order numberDWF50202-104-7 TypeRigger boot, no laces SizeEU 41 (UK 7) ClassificationS3 WR HRO SRA StandardEN ISO 20345:2011 Toe capComposite, non-metallic Underfoot protectionNon-metallic anti-penetration midsole Metal contentNone - 100% non-metallic construction UpperBrown nubuck with anti-scuff toe guard LiningWaterproof and breathable OutsoleDual-density PU/rubber Outsole heat resistanceContact heat to 300 °C (HRO) InsolePU comfort insole ColourBrown Questions and Answers What size are these boots? Order number DWF50202-104-7 corresponds to UK 7, which is EU 41. The number after the final hyphen is the UK size; add 34 to get the European size. What does the S3 WR HRO classification mean? S3 denotes safety footwear with a toe cap, an anti-penetration midsole, antistatic properties, energy absorption in the heel and a water-resistant upper. WR adds a whole-boot water resistance rating, and HRO means the outsole is tested against contact heat up to 300 °C. Is there any metal in the construction? No. The toe cap is composite and the midsole is non-metallic, so the boot is 100% non-metallic. That makes it lighter than its steel equivalent, stops cold conducting through to your toes, and means it will not trigger metal detectors. What is a rigger boot and how is it different? A rigger is a laceless boot with a tall shaft and two pull-on loops. The advantages are speed and..

DeWalt Millington Brown Rigger Boots, Size 45 (UK 11), DWF50202-104-11 DeWalt Millington Brown (order number DWF50202-104-11) is a rigger-style safety boot in EU size 45, which corresponds to UK 11. It is classified S3 WR HRO SRA to EN ISO 20345. A rigger boot has no laces at all - it is pulled on and off by the two loops at the top of the shaft, which matters on sites where boots come off and go back on several times a day. Fully non-metallic construction The Millington is 100% non-metallic: the toe cap is composite and the anti-penetration midsole is non-metallic as well. That has three practical consequences. The boot is noticeably lighter than its steel equivalent at the same protection rating. It creates no cold bridge - a steel toe cap conducts outside cold straight to your toes, and in winter you feel that within the first hour. And it will not set off metal detectors, which matters at airports, in plants that screen for metal, and around sensitive instrumentation. Upper and waterproofing The upper is brown nubuck leather with a tall shaft that covers the ankle and the lower calf. Inside sits a waterproof breathable lining. The membrane works in both directions - it keeps water out while letting perspiration vapour escape - and this is exactly what separates a genuinely waterproof boot from a merely treated one, where your foot ends up damp from its own moisture after a few hours. An anti-scuff toe guard sits over the toe area and takes the abrasion from kneeling and from pushing material with the front of the boot, which is where nubuck otherwise wears through first. Outsole and heat resistance The outsole is dual-density PU/rubber. The polyurethane midlayer does the cushioning while the rubber outer layer absorbs the wear and delivers the grip. The HRO marking in the classification means tested resistance to contact heat up to 300 °C - relevant around hot asphalt, welding bays and roofing membranes. The tread is deeply cleated with a defined heel. Rigger versus laced boot Choosing between the two is not a matter of taste. A rigger goes on in seconds and has no laces to snag or come undone, which is why it is the default in the oil industry, on scaffolding, in agriculture and anywhere people step in and out repeatedly. The trade-off is that the fit cannot be adjusted: the boot has to suit your calf and your instep as it comes. If you have a high instep or a fuller calf, a laced model gives you more room to work with. Choosing your size The order number ends with the UK size and the European size is that number plus 34 - so UK 11 is EU 45. Trying rigger boots on matters more than with a laced model, because there is no way to tighten the fit afterwards. Try them in the afternoon, when your foot has swollen slightly, and with the socks you actually work in: a composite toe cap does not give, and pressure across the toes will not break in with wear. Who they are for The Millington is aimed at construction and installation crews, plant and machinery operators, warehouse and transport work, utilities and agriculture - anywhere you stand and walk all day, the ground is wet, and a dropped object or a nail underfoot is a real risk. Safety footwear remains the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries measured in months of recovery. Technical specifications ModelDeWalt Millington Brown Order numberDWF50202-104-11 TypeRigger boot, no laces SizeEU 45 (UK 11) ClassificationS3 WR HRO SRA StandardEN ISO 20345:2011 Toe capComposite, non-metallic Underfoot protectionNon-metallic anti-penetration midsole Metal contentNone - 100% non-metallic construction UpperBrown nubuck with anti-scuff toe guard LiningWaterproof and breathable OutsoleDual-density PU/rubber Outsole heat resistanceContact heat to 300 °C (HRO) InsolePU comfort insole ColourBrown Questions and Answers What size are these boots? Order number DWF50202-104-11 corresponds to UK 11, which is EU 45. The number after the final hyphen is the UK size; add 34 to get the European size. What does the S3 WR HRO classification mean? S3 denotes safety footwear with a toe cap, an anti-penetration midsole, antistatic properties, energy absorption in the heel and a water-resistant upper. WR adds a whole-boot water resistance rating, and HRO means the outsole is tested against contact heat up to 300 °C. Is there any metal in the construction? No. The toe cap is composite and the midsole is non-metallic, so the boot is 100% non-metallic. That makes it lighter than its steel equivalent, stops cold conducting through to your toes, and means it will not trigger metal detectors. What is a rigger boot and how is it different? A rigger is a laceless boot with a tall shaft and two pull-on loops. The advantages are ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 41 (UK 7), DWF50140-133-7 DeWalt Newark Brown Buffalo (order number DWF50140-133-7) is protective work footwear with a mid cut profile in EU size 41, corresponding to UK 7. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 7 is EU 41. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-7 SizeEU 41 (UK 7) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-7 corresponds to UK size 7, that is EU 41. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 42 (UK 8), DWF50140-133-8 DeWalt Newark Brown Buffalo (order number DWF50140-133-8) is protective work footwear with a mid cut profile in EU size 42, corresponding to UK 8. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 8 is EU 42. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-8 SizeEU 42 (UK 8) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-8 corresponds to UK size 8, that is EU 42. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 44 (UK 10), DWF50140-133-10 DeWalt Newark Brown Buffalo (order number DWF50140-133-10) is protective work footwear with a mid cut profile in EU size 44, corresponding to UK 10. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 10 is EU 44. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-10 SizeEU 44 (UK 10) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-10 corresponds to UK size 10, that is EU 44. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 45 (UK 11), DWF50140-133-11 DeWalt Newark Brown Buffalo (order number DWF50140-133-11) is protective work footwear with a mid cut profile in EU size 45, corresponding to UK 11. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 11 is EU 45. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-11 SizeEU 45 (UK 11) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-11 corresponds to UK size 11, that is EU 45. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

Milwaukee Flextred BEIGE S3S Safety Boots, Size 42, 4932493746DescriptionThe Milwaukee Flextred BEIGE S3S (4932493746) are professional high-cut safety boots designed to provide outstanding protection, comfort, and stability for construction, industrial, maintenance, and logistics applications. Size 42, certified to EN ISO 20345:2022 S3S ESD SC FO SR. The boots feature a water-repellent nubuck leather upper that protects against water, dust, and dirt. ENERGY FOAM heel cushioning delivers excellent comfort and energy return, while the ROLLCAGE™ heel stabilizer enhances stability on uneven terrain. Additional features include the STEP-RELEASE™ heel for quick removal, a lace pocket to secure the laces, a durable TPU scuff cap, and a metal-free construction for easy passage through security gates. The boots are ESD certified, feature an oil-resistant outsole (FO), and provide slip resistance (SR) for reliable performance in demanding working environments.Technical Specifications Brand: Milwaukee Model: Flextred BEIGE S3S Size: 42 Type: High-cut safety boots Colour: Beige Upper: Water-repellent nubuck leather Toe cap: Fiberglass Penetration-resistant midsole: Non-metallic composite Construction: Metal-free Heel cushioning: ENERGY FOAM Heel stabilizer: ROLLCAGE™ Heel release: STEP-RELEASE™ Toe protection: TPU Scuff Cap ESD certified: Yes Oil-resistant outsole: FO Slip resistance: SR Standard: EN ISO 20345:2022 S3S ESD SC FO SR Package Includes 1 x Pair of Milwaukee Flextred BEIGE S3S Safety Boots, Size 42..

Milwaukee FLEXTRED S1PS 1L110133 Safety Footwear, Size 46 Milwaukee FLEXTRED 1L110133 (article number 4932493698, EU size 46) is protective work footwear with a low cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels, black. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1L110133 Article number4932493698 SizeEU 46 StandardEN ISO 20345:2022 Protection classS1PS Profilelow cut (below the ankle) Uppertextile with reinforced nubuck panels, black Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493698 corresponds to EU size 46. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 37 Milwaukee FLEXTRED 1M110133 (article number 4932493702, EU size 37) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493702 SizeEU 37 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493702 corresponds to EU size 37. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 40 Milwaukee FLEXTRED 1M110133 (article number 4932493705, EU size 40) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493705 SizeEU 40 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493705 corresponds to EU size 40. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 43 Milwaukee FLEXTRED 1M110133 (article number 4932493708, EU size 43) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493708 SizeEU 43 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493708 corresponds to EU size 43. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 46 Milwaukee FLEXTRED 1M110133 (article number 4932493711, EU size 46) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493711 SizeEU 46 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493711 corresponds to EU size 46. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..