Knipex 95 31 280 Cable CuttersDescription: The Knipex 95 31 280 automatic ratchet cable cutters are designed for cutting both single- and multi-strand copper and aluminum cables. They are not suitable for cutting steel wire or ropes. The blades are hardened and feature precision-ground cutting edges, ensuring a smooth and clean cut without crushing the material. Working with these pliers is comfortable and easy, as they operate with a single-action ratchet mechanism. This requires less effort thanks to the high gear ratio. The pliers feature a two-stage ratchet mechanism, which facilitates the cutting process. With their compact design and minimal weight, they are easy to handle and allow for work even in tight spaces without the risk of injury. They are made of special tool steel that is forged and oil-hardened, ensuring the tool's long service life and reliability. They can be successfully used for cutting aluminum conductors with a cross-section of up to 4 x 150 mm2, including sector cables. The fixed joint's housing with a support surface allows for stable positioning of the pliers during cutting. Technical specifications:REACH compliance: does not contain SVHCRoHS compliance: not applicableCutting capacity for stranded Cu cable: 380 mm2Cutting capacity for Cu cable, braided Ø 52 mmDimensions: 280 x 131 x 34 mmWeight: 0.860 kg..

Knipex 95 16 160 Cable CuttersDescription: The Knipex 95 16 160 cable cutters have a length of 160 mm and are equipped with insulated, multi-component handles that are VDE-tested. Working with these shears is up to 40% easier compared to standard cable shears of the same length. They can cut multi-strand copper and aluminum cables with a diameter of up to 15 mm (50 mm2) and solid copper and aluminum cables with a cross-section of up to 5 x 4 mm2. The cutting edges are additionally induction-hardened, with a hardness of approximately 56 HRC, ensuring strength and durability during use. *Not suitable for steel wire or hard-drawn copper conductors! Technical specifications:Cutting range: 50 mm2, ⌀ Ø 15 mmMaterial: chrome-plated electrical steelStandard: DIN EN 60900, IEC 60900Dimensions: 160 x 60 x 28 mmWeight: 0.225 kg..

Bosch Pro Pruner 06019K1021 Cordless Pruning ShearsThe Bosch Pro Pruner cordless garden shears are designed for cutting branches with less physical effort and a clean, even cut. The model operates on a 12 V Li-Ion battery and is suitable for vineyard and orchard work, as well as general garden maintenance. The blades are made of stainless steel, and the design includes a battery status indicator.The tool is designed to cut branches up to 25 mm thick and can make up to 4,500 cuts on a single charge. The body is compact, and the low weight without the battery facilitates prolonged use. The set includes two GBA 12V 3.0Ah rechargeable batteries, a GAL 12V-20 Professional charger, and maintenance accessories.Technical specifications:Product type: cordless garden shears / prunersModel: Pro PrunerCatalog number: 06019K1021Battery type: Li-IonBattery voltage: 12 VMaximum cutting capacity: 25 mmNumber of cuts per charge: up to 4,500Blade material: stainless steelWeight without battery: 0.8 kgLength: 302 mmWidth: 55 mmHeight: 99 mmIncluded:2 x GBA 12V 3.0Ah rechargeable batteryGAL 12V-20 Professional chargerReversible screwdriver13 mm socketTORX bit with 1/4" hex shank..

Knipex 97 53 04 Crimping ToolDescription: The Knipex 97 53 04 crimping pliers are specially designed for side crimping with square compression of cables and terminals in accordance with DIN 46228. This ensures optimal contact at the connections, providing a reliable and secure connection. The crimping size is automatically adjusted up to 16 mm2, and the pliers are factory-calibrated with a precision lever system. This tool offers the perfect combination of ergonomic design and low weight, making it easy to use and carry. The pliers have a capacity of 0.08 to 16 mm2, and are made of special chrome-vanadium steel that is oil-hardened for greater strength and durability. They are a reliable and convenient tool for professional and home use. Technical specifications:Length, mm: 180 mmAWG: 28-5Wire cross-section: 0.08-10 + 16 mm2Material: CrV steelInsulation type: multi-component coatingVDE tested at 1000 V: NoStandard: DIN 46228Weight: 0.405 kg..

DeWALT DWHT14687-0 Sheet Metal Crimping Shears..

DeWALT DWHT14692-0 Sheet Metal Crimping Shears..

The DEWALT® Ergo Aviation Hacksaw is designed with a reduced grip width, reducing the amount of muscle effort required when cutting through tough materials. This tool is traditionally used for cutting aluminum, vinyl siding, plywood, cardboard, leather, copper, and sheet metal from 18 to 22 gauge. The serrated cutting edge of the blade prevents materials from slipping during use, and the slip-resistant, bi-material cushion grip ensures a secure, comfortable grip...

DeWALT DWHT14675-0 Straight Sheet Metal Shears..

DeWALT DWHT14694-0 Straight Sheet Metal Shears..

Knipex 95 05 10 SB Cable CuttersDescription: The Knipex 95 05 10 SB electrical shears have a length of 155 mm and are equipped with stainless steel cutting heads featuring cutting edges with a hardness of 56 HRC. They are designed with precision-ground blades, ensuring efficient cutting. Intended for cutting copper and aluminum wires, they offer high precision during operation. The handles are multi-component and made of fiberglass, ensuring a comfortable and secure grip during use. Technical specifications:Length: 155 mmHandles: fiberglass, multi-componentCutting heads: stainless steelWith plastic protectorWeight: 0.110 kg..

Knipex 95 05 155 SB Cable CuttersDescription: The Knipex 95 05 155 SB electrical shears have a length of 155 mm and are equipped with stainless steel cutting heads featuring cutting edges with a hardness of 56 HRC. They are designed with precision-ground blades, ensuring efficient cutting. Intended for cutting copper and aluminum wires, they offer high precision during operation. The handles are multi-component and made of fiberglass, ensuring a comfortable and secure grip during use. Technical specifications:Length: 155 mmHandles: fiberglass, multi-componentCutting heads: stainless steelWith plastic protectorWeight: 0.325 kg..

Knipex 99 04 250 Rebar CuttersDescription: The Knipex 99 04 250 chrome-plated rebar cutters feature a total length of 250 mm and a cutting range from ⌀ 1.6 to 2.4 mm. They offer high cutting capacity with minimal effort, making them effective tools for the job. The cutting edges are additionally hardened to a hardness of approximately 61 HRC, ensuring durability and a long tool life. Suitable for twisting and cutting both soft and hard wires, offering high efficiency and precision in operation. Technical specifications:Cutting range: ⌀ 1.6 - 2.4 mmStandard: DIN ISO 9242Dimensions: 250 x 47 x 25 mmMaterial: steelWeight: 0.405 kg..

Knipex 99 14 250 Rebar CuttersDescription: The Knipex 99 14 250 chrome-plated rebar cutters feature a length of 250 mm and a cutting capacity of up to 3.3 mm. They are made of forged and oil-hardened special tool steel, ensuring exceptional strength and durability. The pliers' hinge has a high gear ratio, ensuring smooth and efficient movement. With these pliers, twisting and cutting the wire is done in a single operation, which improves productivity and work efficiency. The cutting edges are additionally hardened to a hardness of 61 HRC, making them exceptionally sharp and durable. The pliers' handles are not insulated, which can provide better control and feel during use. Suitable for various applications in construction and metalworking. Technical specifications:Length: 250 mmVDE tested at 1000V: noRockwell hardness: 61 HRCCutting capacity for medium-hard wire: 3.3 mmCutting capacity for hard wire: 1.8 mmCoating: chromeJaw coating: polishedManufacturing method: forged, hardenedStandard: DIN ISO 9242Weight: 0.35 kg..

Knipex 95 61 190 Wire Cutting PliersDescription: Knipex 95 61 190 steel rope cutters are made of high-quality forged and oil-hardened chrome-vanadium steel, with the cutting edges additionally induction-hardened to a hardness of approximately 64 HRC, ensuring their durability and strength. The special blade geometry is designed to prevent the wires from unraveling when cutting the rope. They are comfortable to use, featuring a bolt for precise blade alignment and subsequent adjustment. Additionally, they feature 2 extra slots that allow for crimping pipe ends, steel coils, and wires. They are 190 mm long and have a cutting capacity of up to 5 mm (on hard material-up to 2.5 mm), ideal for professional applications where reliable and precise cutting of steel cables is required. Technical specifications:Conductor cross-section: 10 mm2Material: CrV steelInsulation type: plastic coatingVDE tested at 1000 V: noJaw shape: side-sharpenedRockwell hardness: 64 HRCCutting capacity for soft wire: 5 mmCutting capacity for medium-hard wire: 4 mmHard wire cutting capacity: 2.5 mmCutting capacity for copper stranded cable: 7 mmSteel rope cutting capacity: 4 mmJaw coating: polishedManufacturing method: induction hardenedAdditional features: with opening springLength, mm: 190 mmWeight: 0.314 kg..

Milwaukee Bypass Loppers, up to 50 mm, 4932498625 Milwaukee article number 4932498625 is a bypass lopper with a cutting capacity of up to 50 mm and 690 mm aluminium handles. It is built for maintaining trees and shrubs, shaping crowns and clearing dead wood. Bypass rather than anvil - and why that matters Loppers come in two types and the difference is not cosmetic. On a bypass tool the two blades pass each other like scissors, producing a clean, smooth cut. On an anvil tool a single blade presses the branch against a flat plate and crushes it. On living wood that is decisive: crushed tissue heals slowly and is an entry point for fungal infection, while a clean bypass cut closes quickly. Anvil designs only make sense on dry, dead wood, where there is nothing left to damage. Forged steel blades The blades are forged steel. On a lopper the load concentrates into a very small area, and that is exactly where cheap tools give up - the blade bends sideways, the two halves stop passing each other accurately, and from then on the tool crushes instead of cutting. Forged steel holds its geometry under load. The blade profile is shaped so that the branch is drawn towards the pivot as the jaws close, rather than sliding outwards where the leverage is weakest. 690 mm aluminium handles The handles are aluminium and 690 mm long. The two things work together: length provides the leverage needed for a 50 mm branch in hardwood, while aluminium keeps the weight down so the tool can be used overhead without your arms giving out after a few cuts. Steel handles of the same length would be noticeably heavier. Two gripping zones The handles offer two gripping zones with a rubber overmould. The outer position gives maximum leverage for thick branches, the inner one gives control for precise cuts on thin growth. In practice that means you do not swap tools when moving between shaping and serious cutting. When to prune Most fruit and ornamental species are pruned during dormancy - from late winter to early spring, before the buds swell. Make the cut just above a bud or at the branch collar, leaving no stub, because a stub dries out and becomes a source of rot. Clean the blades between trees if you are working with diseased plants - a lopper carries infection just as reliably as it cuts. Maintenance After use, clean sap and resin off the blades and wipe them dry - a wet blade will rust overnight. A thin film of oil on the blade and in the pivot extends the tool's life and reduces the effort of cutting. A blunt blade announces itself by tearing the bark instead of slicing through it. Technical specifications ManufacturerMilwaukee Article number4932498625 TypeBypass lopper Maximum cutting diameter50 mm Handle length690 mm Blade materialForged steel Handle materialAluminium GripsTwo gripping zones, rubber overmould UsePruning trees and shrubs, shaping, dead wood Questions and Answers What is the difference between bypass and anvil loppers? On a bypass tool the blades pass each other like scissors and produce a clean cut - the type for living wood. On an anvil tool the blade presses the branch against a flat plate and crushes it; it suits dry, dead wood only. This model is bypass. Will it really cut a 50 mm branch? 50 mm is the maximum and refers to normal timber. On very hard species, or on dry, seasoned wood, work to a smaller diameter or reach for a saw - forcing the tool bends the blades. What are the two gripping zones for? The outer position gives maximum leverage on thick branches, the inner one gives better control for precise cuts on thin growth. That way you do not have to change tools when switching between the two kinds of work. When is the right time to prune? For most fruit and ornamental species, during dormancy - late winter to early spring, before the buds swell. Cut just above a bud or at the branch collar, leaving no stub behind. Why aluminium handles? The 690 mm length is needed for leverage on a thick branch, but with steel handles the tool would be noticeably heavier. Aluminium keeps the strength at far lower weight - which matters most when working overhead. How do I look after the blades? Clean sap and resin off after use and wipe them dry - a wet blade rusts overnight. A thin film of oil on the blade and in the pivot extends the life of the tool and reduces cutting effort. How do I know the blade has gone blunt? A blunt lopper starts tearing the bark instead of slicing it, leaving a ragged edge to the cut. That is also where fungal infection begins, so bluntness is not only a question of effort. ..

Milwaukee Bypass Pruning Shears, up to 25 mm, with Sheath, 4932499679 Milwaukee article number 4932499679 is a hand bypass pruning shear with a cutting capacity of up to 25 mm. A belt sheath is included. The blades are steel, and the handles are shaped to fit hands of different sizes. Bypass - the type for living wood On a bypass pruner the two blades pass each other like ordinary scissors and leave a clean cut. The alternative - anvil - presses the branch against a flat plate and crushes it. On living wood the difference is decisive: crushed tissue heals slowly and is an entry point for fungal infection, while a clean bypass cut closes quickly. That is why bypass is used for pruning live plants, with anvil reserved for dry, dead wood. Two-position locking The pruner locks in two positions. The first is the usual closed lock for storage - it will not spring open in the sheath or a pocket. The second is more interesting: it limits how far the blades open. When working on thin growth only, full opening is wasted movement repeated hundreds of times a day. Limiting the travel reduces that, and with it hand fatigue - a real difference over a full morning of pruning. Sheath with a metal clip The sheath has a flexible back panel and a metal belt clip. The metal clip matters: plastic ones snap the first time they catch on a branch or a trellis wire. The sheath is multi-fit and takes both this 25 mm model and the 20 mm one from the same range. Maximum height for the clip and belt loop is 50 mm, which covers standard work belts. 25 mm capacity 25 mm is the upper limit for a hand pruner of this class and refers to normal timber. On harder species, or on dry, seasoned wood, work to a smaller diameter or move up to long-handled loppers. Forcing a pruner bends the blades, after which they no longer pass each other accurately - and from then on the tool crushes instead of cutting. Cutting properly Place the branch deep towards the pivot, where the leverage is greatest, not out at the blade tips. Cut at a slight angle, just above a bud or at the branch collar, leaving no stub - a stub dries out and becomes a source of rot. When working with diseased plants, disinfect the blades between plants: a pruner carries infection just as reliably as it cuts. Maintenance After use, clean sap and resin from the blades and wipe them dry - a wet blade rusts overnight. A thin film of oil in the pivot reduces effort and prevents seizing. A blunt blade announces itself by tearing the bark instead of slicing it. Technical specifications ManufacturerMilwaukee Article number4932499679 TypeBypass pruning shears Maximum cutting diameter25 mm BladesSteel LockingTwo positions - closed and limited opening HandlesErgonomic, suited to different hand sizes SheathIncluded, flexible back panel with metal clip Sheath compatibility20 mm and 25 mm models Maximum clip height50 mm Questions and Answers What is the difference between bypass and anvil? On a bypass tool the blades pass each other like scissors and leave a clean cut - the type for living wood. On an anvil tool the blade crushes the branch against a flat plate; it suits dry, dead wood only. This model is bypass. Will it really cut a 25 mm branch? 25 mm is the maximum and refers to normal timber. On hard species or dry, seasoned wood, work to a smaller diameter - forcing the tool bends the blades, and they then stop passing each other accurately. What are the two lock positions for? The first locks the tool closed for storage. The second limits how far the blades open - on thin growth that shortens the stroke and reduces hand fatigue, which you notice after a full morning of pruning. Is a sheath included? Yes - a sheath with a flexible back panel and a metal belt clip. The metal clip does not snap when it catches on a branch, unlike plastic ones. The sheath also takes the 20 mm model from the same range. Where exactly should the branch sit in the jaws? Deep towards the pivot, where the leverage is greatest, not at the blade tips. Cutting with the tips takes many times more effort and is the most common cause of bent blades. Should I disinfect the blades? When working with diseased plants, yes - between plants. A pruner carries fungal and bacterial infection just as reliably as it cuts. How do I look after the blades? Clean sap and resin off after use and wipe the blades dry - a wet blade rusts overnight. A thin film of oil in the pivot reduces effort. A blunt pruner starts tearing the bark instead of slicing it. ..

Milwaukee 4932478620 Wire CutterDescription:Milwaukee 4932478620 electrician's pliers suitable for crimping cables up to 6 mm . The pliers' design allows for easy stripping of wires. The adjustable tension screw allows you to set the desired resistance. Extremely sturdy handles for better grip and control. Equipped with a sheath and belt clip for easy storage...