Consumables for tools - Page 26

STROXX SDS-Max 4CUT Hammer Drill Bit, 18 x 540 x 400 mm, 500-607 STROXX 500-607 is an SDS-Max hammer drill bit with a four-cutter carbide head. Diameter 18 mm, overall length 540 mm, working (flute) length 400 mm. PGM approved. EAN 5707436095406. Why four cutters A classic bit has two cutters and does well in clean concrete. The trouble starts at the rebar: two cutters catch the steel at an angle, the bit rocks, and it either breaks or wanders off line. With four cutters the load spreads over twice as many points, the bit goes through reinforcement without deflecting, and the hole stays round. The two lengths 540 mm is the overall length, while 400 mm is the fluted section - meaning the maximum drilling depth is 400 mm. The remaining 140 mm are the shank and the smooth zone, which carry no dust. That is the distinction most often missed when ordering: a 540 mm bit does not make a 540 mm hole. The SDS-Max fitting SDS-Max is the standard for heavy rotary hammers, from the 5 kg class upwards. The shank pushes in and clicks with no key, and the internal play lets the bit travel along its axis on every blow. An SDS-Max bit will not fit an SDS-plus machine, or the other way round. Dust removal The flute has a wide channel for fast dust removal. At 400 mm of depth that is decisive: if the dust stays at the bottom, the bit starts working on its own spoil, loses speed and overheats the head. When to replace the bit A carbide head does not fail suddenly - it loses its edge gradually, and the signs are felt before they are seen. The first is that drilling takes noticeably longer at the same pressure. The second is smoke and a burnt smell from the hole. The third is spoil coming out finer than usual - instead of cutting flakes, a dull head grinds the material. Working with a blunt bit is not merely slow: it loads the hammer mechanism of the machine and costs more than a new bit. What it is for Reinforced concrete - structural anchors, passing through a wall or slab for services, fixing heavy equipment. An 18 mm diameter suits M12 anchors in most systems. Technical specifications ManufacturerSTROXX Article number500-607 TypeSDS-Max hammer drill bit Cutters4 Diameter18 mm Overall length540 mm Working length400 mm HeadCarbide ApprovalPGM MaterialsReinforced concrete, stone, masonry EAN5707436095406 Questions and Answers What is the maximum hole depth? 400 mm - that is the fluted section. Overall length is 540 mm, but the remaining 140 mm are shank and smooth zone which carry no dust. What do four cutters give you? The load spreads over twice as many points, so the bit goes through rebar without deflecting and the hole stays round. With two cutters the bit rocks in the steel. Will it fit my machine? Only if the machine takes SDS-Max - the standard on heavy rotary hammers from the 5 kg class up. It will not fit SDS-plus. Which anchors suit 18 mm? It matches M12 anchors in most systems - structural fixing and heavy equipment mounting. Can it drill through reinforcement? Yes - that is the point of the four-cutter head. Reinforced concrete is the target material. What does PGM mean? Approval under the German quality scheme for concrete drill bits - assurance that the actual hole diameter matches the stated one. Why does dust removal matter? At 400 mm of depth, if the dust stays at the bottom the bit works on its own spoil, loses speed and overheats the head. ..

Big Wipes Heavy-Duty Hand Cleaning Wipes, 100 Pieces Big Wipes Heavy-Duty are textured wipes for cleaning hands, tools and surfaces. The tub has a red cap and holds 100 wipes. This is the Big Wipes line built first and foremost for hands. The two sides The wipe works by dual action: one side is textured and scrubs, the other is smooth and lifts. In practice you scrub with the rough side until the dirt releases, then turn the wipe so it does not go straight back on. That is the difference from ordinary wet wipes, which mostly move the oil around. What it removes The tub lists paint, adhesive, PU foam, silicone, gap fill and oil. That list is why these live in the van: PU foam and silicone are the two things that get on your hands on site and come off with neither soap nor an ordinary wet wipe. Foam has to be caught before it cures - after that nothing shifts it. Not only for hands The same wipe cleans the tool housing, the handles, a spirit level's window, the case and the van dashboard. One item on the shelf instead of two - a hand cleaner and a tool cleaner. The 100-wipe tub 100 wipes is the van and workshop format. The tub opens one-handed and the wipes pull through the centre hole. The cap has to go back on - it is the only thing keeping them wet, and a tub left open loses the top few. Fragrance This run carries the Sports Active fragrance. A small thing, but it matters working indoors, where the strong solvent smell of some competitors is unpleasant for the whole crew. Telling the range apart Big Wipes codes the range by cap colour: red is Heavy-Duty, green is Multi-Surface. The tub body is yellow on both, so when ordering, look at the cap and not the tub. Technical specifications ManufacturerBig Wipes RangeHeavy-Duty Cap colourRed Quantity100 wipes TypeTextured, dual action Use onHands, tools and surfaces RemovesPaint, adhesive, PU foam, silicone, gap fill, oil FragranceSports Active Questions and Answers How many wipes are in the tub? 100. What is the difference between the red and green tubs? The red cap is Heavy-Duty - textured, for hands. The green is Multi-Surface. Both bodies are yellow, so go by the cap. Do they remove silicone and PU foam? Yes - both are listed on the tub. Foam must be caught before it cures. Why does the wipe have two sides? Dual action: the textured side scrubs, the smooth side lifts. Turning the wipe stops the dirt going back on. Are they only for hands? No. The same wipe cleans tools, machines and surfaces - housings, handles, cases, the van dashboard. How do I stop them drying out? Put the cap back on every time. A tub left open loses the top few wipes. What does it smell like? Sports Active fragrance - without the strong solvent smell of some competitors. ..

BOSCH 2608000495 Reciprocating Saw Blade Set with Two Blades The Bosch 2608000495 blade set includes two interchangeable blades (922 VF and 922 EF) for cutting wood and metal. The 922 VF is a versatile blade for wood and metal and is ideal for use with construction lumber, softwood, sheet metal, and glass-fiber-reinforced plastic. The 922 EF blade is ideal for sheet metal, epoxy resin, and glass-fiber-reinforced plastic. The pocket saw's handle features a quick-release mechanism that allows you to change blades quickly and safely. Designed for professional craftsmen and DIY enthusiasts, each blade features different teeth, allowing you to tackle smaller cutting tasks with ease and efficiency. Included:BOSCH 2608000495 handle;1 S 922 EF Flexible metal blade;1 S 922 VF Flexible wood and metal blade...

Milwaukee HEPA Filter for M18 VC Vacuum, 4931454785 Milwaukee 4931454785 is a genuine HEPA filter for the M18 VC cordless wet and dry vacuum. Supplied singly. EAN 4058546014025. What HEPA means HEPA is a filter class that retains the finest particles - those under a micron, which an ordinary filter simply passes back into the room. On site those are exactly the problem: silica dust from concrete and plaster is invisible in the air, harmful to the lungs, and still settling hours after the work has finished. When to replace it Replace the filter when suction drops noticeably even after cleaning, or when the pleats have greyed through their full depth and do not recover on tapping. Working with a blocked filter is not merely slower - the motor works against resistance, draws more current and runs hot. Cleaning between changes Clean the filter by tapping it out or blowing from the inside outwards. Do not wash it in water unless the maker states it is washable - wet filter media distorts as it dries and then leaks. Work the pleats along their length, not across. Wet and dry with one filter Wet and dry machines carry one rule that is broken more than any other: the filter comes out before wet pick-up. Left in, water soaks the filter media, the pleats stick together, and once dry the filter no longer passes air - suction halves and never recovers. If it does get wet, let it dry completely in air, never on a radiator and never with hot air: heat distorts the plastic frame and the rim seal stops seating. Compatibility The filter is for the M18 VC vacuum - the older model in Milwaukee's wet and dry range. It is worth comparing the designation on the machine's housing before ordering. A genuine part This is a genuine Milwaukee filter, article 4931454785. With filters, fit is not only a matter of size: the seal around the rim has to sit exactly, or the dust travels past the filter and the whole HEPA rating counts for nothing. Technical specifications ManufacturerMilwaukee Article4931454785 TypeHEPA filter For machineM18 VC Quantity1 piece ClassHEPA ApplicationWet and dry vacuum cleaner EAN4058546014025 Questions and Answers Which machine is it for? The Milwaukee M18 VC cordless wet and dry vacuum. Compare the designation on the machine's housing before ordering. What does HEPA mean? A filter class that retains the finest particles - under a micron. An ordinary filter passes them back into the room. Why does it matter on site? Silica dust from concrete and plaster is invisible in the air, harmful to the lungs, and still settling hours after work. When should it be replaced? When suction drops noticeably even after cleaning, or the pleats have greyed through their full depth and do not recover. Can it be washed? Not unless the maker states it is washable. Wet filter media distorts as it dries and then leaks. How is it cleaned? By tapping it out or blowing from the inside outwards, along the pleats rather than across them. Is it a genuine part? Yes - a genuine Milwaukee filter, article 4931454785. The rim seal has to sit exactly, or dust travels past the filter. ..

STROXX Hex Key Set, Colour-Coded, 9 Pieces, 1.5-10 mm, 100-770 STROXX 100-770 is a set of nine long-arm hex keys in sizes from 1.5 to 10 mm, each in its own colour, with a ball end on the long arm and a plastic holder. EAN 5707436069582. The colour is a function, not decoration The nine keys are powder-coated in different colours, and the size is printed on the holder below each slot. When you are working with fasteners in several sizes - typical on furniture, bicycles, machine covers and aluminium profiles - hunting for the right key disappears. Once learned, a colour is recognised from a distance and with dirty hands, which in practice beats reading a stamped size. The ball end The long arm ends in a ball point. It engages the screw socket at angles up to roughly 25-30° and lets you drive fasteners where the key cannot be brought square - behind a rib, down a recess, close to a wall. The straight end on the short arm stays for final tightening and for breaking a fastener loose: that is where the load peaks and it has to be carried by the full wall of the socket, or the hex rounds out. Long arms These are the long-arm series. The long arm not only reaches further - it is noticeably more comfortable: spinning with the long arm gives the hand a wider sweep, and tightening with the short arm turns the long one into a proper lever. The finish is nickel-plated and powder-coated, a combination that stops rust while holding the colour. The holder The set comes in a plastic holder with a slot for every size and a hanging hole. Keys come out and go back one at a time and stay in size order - the difference between a set that is still complete six months on and a handful of keys loose in the bottom of a bag. Sizes in the set 1.5 mm, 2 mm, 2.5 mm, 3 mm, 4 mm 5 mm, 6 mm, 8 mm, 10 mm Technical specifications ManufacturerSTROXX Article number100-770 EAN5707436069582 TypeHex keys (L-shaped) Pieces9 Sizes1.5 / 2 / 2.5 / 3 / 4 / 5 / 6 / 8 / 10 mm Long armBall end Short armStraight hex Arm lengthLong-arm series FinishNickel-plated, powder-coated Colour codingYes, by size HolderPlastic, slot per size, hanging hole Questions and Answers Which sizes are in the set? Nine metric sizes - 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm. That is the standard range for furniture and machine fasteners. There are no imperial sizes. What is the ball end for? It lets you drive a fastener at up to roughly 25-30° off the screw axis - behind a rib, down a recess or close to a wall, where the key cannot be brought square. Use it for spinning fasteners in and out, not for final tightening. Which end do I tighten with? The straight hex on the short arm. There the load is carried by the full wall of the socket. Tightening or breaking loose a tight fastener with the ball end puts the load on a small contact patch and rounds the socket out. Why are the keys different colours? The colour codes the size. When you are working across several sizes, the eye picks up a colour far faster than it reads a stamped number - especially in poor light and with dirty hands. The holder also prints the size in figures below each slot. What do the long arms give me? Reach to deeper-set fasteners, and more leverage. Spinning with the long arm gives the hand a wider sweep; tightening with the short arm turns the long arm into a long lever, so the same effort produces more torque. Will they rust? The surface is nickel-plated and powder-coated on top. The nickel stops corrosion and the powder coat holds the colour while adding protection. Even so, dry the keys if they have been stored in a wet bag - the coating protects the steel only while it is intact. Can they be used in a power tool? No. These are hand-held L-keys, not bits. Machine work needs hex bits or sockets with a 1/4" or 1/2" drive, built to take impact loading. ..

Dremel Wood Carving Bit 26150115JADescription: The Dremel high-speed router bit is ideal for shaping, carving, grooving, cutting, and making tapered holes in soft metals, plastic, and wood. The durable Dremel Max Carving Bit 115JA is coated with titanium nitride to last twice as long as standard uncoated accessories. Let the accessory and your Dremel Multi-Tool do the work without forcing or pressing too hard. For best results, use the sides of the accessory head at an angle of less than 90 degrees.Technical specifications:Accessory length: 38 mmHead type: rectangular headMax. RPM: 30,000 rpmShaft diameter: 3.2 mmWorking diameter: 7.8 mmQuantity per package: 1 pchttps://youtu.be/BriBq3WhewA..

Brand: Milwaukee Model: UC18YFSL Warranty: 2 years..

Fervi PPS150/29M14 Backing Pad, Ø150 mm, Velcro, M14 Fervi PPS150/29M14 is a polyurethane backing pad with a hook-and-loop face for an angle grinder or orbital sander. Diameter Ø150 mm, thickness 29 mm, thread M14, maximum speed 7000 rpm. EAN 8012667325756. What it does The pad is the carrier - it screws onto the machine's spindle and the abrasive discs stick to its hook-and-loop face. Without it an angle grinder can only cut and grind; with it, it becomes a sanding and polishing machine. The polyurethane The body is polyurethane, not rigid plastic. The difference shows immediately: polyurethane flexes slightly and follows the surface instead of working only on its edge. On a slightly domed or uneven substrate that is the difference between even sanding and the arc-shaped marks you then have to sand out again. The 7000 rpm limit 7000 rpm is the ceiling, and it matters: most 125 mm angle grinders run at 11000 rpm and above, so an ordinary grinder without speed control is not suitable. You need a machine with speed electronics - a polisher, or a grinder with a speed dial. The M14 thread M14 is the standard thread on European angle grinders from 115 mm upward. The pad screws straight on, with no adapter. Hand-tight is enough - in use the direction of rotation keeps tightening it. Ø150 or Ø125 Fervi offers the same pad in Ø125 mm (PPS125/27M14, 8000 rpm). Choose by the abrasive discs you work with, not by the machine: a 150 mm disc on a 125 mm pad overhangs the rim and tears. Dry use The pad is for dry sanding. The hook-and-loop face and the adhesive beneath it do not tolerate water - wet use lifts them and after a few cycles the discs stop holding. Technical specifications ManufacturerFervi ArticlePPS150/29M14 TypePolyurethane backing pad, hook-and-loop DiameterØ150 mm Thickness29 mm ThreadM14 Maximum speed7000 rpm ApplicationDry, angle grinder and orbital sander Weight0.17 kg EAN8012667325756 Questions and Answers What diameter is it? Ø150 mm, 29 mm thick. A Ø125 mm version also exists (PPS125/27M14). What thread does it have? M14 - the European standard from 115 mm grinders upward. It screws on directly, no adapter. Will it fit any angle grinder? No. The limit is 7000 rpm, while ordinary 125 mm grinders run at 11000 and above. You need a machine with speed control. How do the discs attach? To the hook-and-loop face. Discs press on and peel off by hand, no tool needed. Why polyurethane rather than plastic? Polyurethane flexes slightly and follows the surface instead of digging with its edge - no arc marks on uneven work. Can it be used wet? No. It is for dry sanding - water lifts the hook-and-loop face. What size discs should I buy? 150 mm. A larger disc overhangs the rim and tears. ..

Milwaukee 4932471566 SHOCKWAVE Impact BitMilwaukee impact bits are specifically designed for use with impact drivers; the SHOCKWAVETM IMPACT DUTY accessory line is not only ideal for heavy-duty impact applications but also offers a comprehensive system solution for all user needs in drilling and fastening. Laser-hardened WEAR GUARD TIPTM for improved wear resistance and tip protection throughout the bit's life. SHOCK ZONETM reduces stress on the tip, resulting in fewer tip breakages. The combination of the SHOCK ZONETM design and special heat treatment absorbs impacts and allows the bit to flex like a spring. Custom-engineered steel-Milwaukee®'s custom metal formula makes SHOCKWAVETM bits more impact-resistant. https://www.youtube.com/watch?v=BCDHTJgWRdE..

Designed for use with impact drivers, the SHOCKWAVETM IMPACT DUTY accessory line is not only ideal for heavy-duty impact applications, but also offers a comprehensive system solution for all user needs in drilling and fastening. Laser-hardened WEAR GUARD TIPTM for improved wear resistance and tip protection throughout the bit's life. SHOCK ZONETM reduces stress on the tip, resulting in fewer tip breakages. The combination of the SHOCK ZONETM design and special heat treatment absorbs impacts and allows the bit to flex like a spring. Custom-engineered steel - Milwaukee®'s custom metal formula makes SHOCKWAVETM bits more impact-resistant. https://www.youtube.com/watch?v=BCDHTJgWRdE..