Workwear - Page 3

DeWalt Millington Brown Rigger Boots, Size 41 (UK 7), DWF50202-104-7 DeWalt Millington Brown (order number DWF50202-104-7) is a rigger-style safety boot in EU size 41, which corresponds to UK 7. It is classified S3 WR HRO SRA to EN ISO 20345. A rigger boot has no laces at all - it is pulled on and off by the two loops at the top of the shaft, which matters on sites where boots come off and go back on several times a day. Fully non-metallic construction The Millington is 100% non-metallic: the toe cap is composite and the anti-penetration midsole is non-metallic as well. That has three practical consequences. The boot is noticeably lighter than its steel equivalent at the same protection rating. It creates no cold bridge - a steel toe cap conducts outside cold straight to your toes, and in winter you feel that within the first hour. And it will not set off metal detectors, which matters at airports, in plants that screen for metal, and around sensitive instrumentation. Upper and waterproofing The upper is brown nubuck leather with a tall shaft that covers the ankle and the lower calf. Inside sits a waterproof breathable lining. The membrane works in both directions - it keeps water out while letting perspiration vapour escape - and this is exactly what separates a genuinely waterproof boot from a merely treated one, where your foot ends up damp from its own moisture after a few hours. An anti-scuff toe guard sits over the toe area and takes the abrasion from kneeling and from pushing material with the front of the boot, which is where nubuck otherwise wears through first. Outsole and heat resistance The outsole is dual-density PU/rubber. The polyurethane midlayer does the cushioning while the rubber outer layer absorbs the wear and delivers the grip. The HRO marking in the classification means tested resistance to contact heat up to 300 °C - relevant around hot asphalt, welding bays and roofing membranes. The tread is deeply cleated with a defined heel. Rigger versus laced boot Choosing between the two is not a matter of taste. A rigger goes on in seconds and has no laces to snag or come undone, which is why it is the default in the oil industry, on scaffolding, in agriculture and anywhere people step in and out repeatedly. The trade-off is that the fit cannot be adjusted: the boot has to suit your calf and your instep as it comes. If you have a high instep or a fuller calf, a laced model gives you more room to work with. Choosing your size The order number ends with the UK size and the European size is that number plus 34 - so UK 7 is EU 41. Trying rigger boots on matters more than with a laced model, because there is no way to tighten the fit afterwards. Try them in the afternoon, when your foot has swollen slightly, and with the socks you actually work in: a composite toe cap does not give, and pressure across the toes will not break in with wear. Who they are for The Millington is aimed at construction and installation crews, plant and machinery operators, warehouse and transport work, utilities and agriculture - anywhere you stand and walk all day, the ground is wet, and a dropped object or a nail underfoot is a real risk. Safety footwear remains the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries measured in months of recovery. Technical specifications ModelDeWalt Millington Brown Order numberDWF50202-104-7 TypeRigger boot, no laces SizeEU 41 (UK 7) ClassificationS3 WR HRO SRA StandardEN ISO 20345:2011 Toe capComposite, non-metallic Underfoot protectionNon-metallic anti-penetration midsole Metal contentNone - 100% non-metallic construction UpperBrown nubuck with anti-scuff toe guard LiningWaterproof and breathable OutsoleDual-density PU/rubber Outsole heat resistanceContact heat to 300 °C (HRO) InsolePU comfort insole ColourBrown Questions and Answers What size are these boots? Order number DWF50202-104-7 corresponds to UK 7, which is EU 41. The number after the final hyphen is the UK size; add 34 to get the European size. What does the S3 WR HRO classification mean? S3 denotes safety footwear with a toe cap, an anti-penetration midsole, antistatic properties, energy absorption in the heel and a water-resistant upper. WR adds a whole-boot water resistance rating, and HRO means the outsole is tested against contact heat up to 300 °C. Is there any metal in the construction? No. The toe cap is composite and the midsole is non-metallic, so the boot is 100% non-metallic. That makes it lighter than its steel equivalent, stops cold conducting through to your toes, and means it will not trigger metal detectors. What is a rigger boot and how is it different? A rigger is a laceless boot with a tall shaft and two pull-on loops. The advantages are speed and..

DeWalt Millington Brown Rigger Boots, Size 45 (UK 11), DWF50202-104-11 DeWalt Millington Brown (order number DWF50202-104-11) is a rigger-style safety boot in EU size 45, which corresponds to UK 11. It is classified S3 WR HRO SRA to EN ISO 20345. A rigger boot has no laces at all - it is pulled on and off by the two loops at the top of the shaft, which matters on sites where boots come off and go back on several times a day. Fully non-metallic construction The Millington is 100% non-metallic: the toe cap is composite and the anti-penetration midsole is non-metallic as well. That has three practical consequences. The boot is noticeably lighter than its steel equivalent at the same protection rating. It creates no cold bridge - a steel toe cap conducts outside cold straight to your toes, and in winter you feel that within the first hour. And it will not set off metal detectors, which matters at airports, in plants that screen for metal, and around sensitive instrumentation. Upper and waterproofing The upper is brown nubuck leather with a tall shaft that covers the ankle and the lower calf. Inside sits a waterproof breathable lining. The membrane works in both directions - it keeps water out while letting perspiration vapour escape - and this is exactly what separates a genuinely waterproof boot from a merely treated one, where your foot ends up damp from its own moisture after a few hours. An anti-scuff toe guard sits over the toe area and takes the abrasion from kneeling and from pushing material with the front of the boot, which is where nubuck otherwise wears through first. Outsole and heat resistance The outsole is dual-density PU/rubber. The polyurethane midlayer does the cushioning while the rubber outer layer absorbs the wear and delivers the grip. The HRO marking in the classification means tested resistance to contact heat up to 300 °C - relevant around hot asphalt, welding bays and roofing membranes. The tread is deeply cleated with a defined heel. Rigger versus laced boot Choosing between the two is not a matter of taste. A rigger goes on in seconds and has no laces to snag or come undone, which is why it is the default in the oil industry, on scaffolding, in agriculture and anywhere people step in and out repeatedly. The trade-off is that the fit cannot be adjusted: the boot has to suit your calf and your instep as it comes. If you have a high instep or a fuller calf, a laced model gives you more room to work with. Choosing your size The order number ends with the UK size and the European size is that number plus 34 - so UK 11 is EU 45. Trying rigger boots on matters more than with a laced model, because there is no way to tighten the fit afterwards. Try them in the afternoon, when your foot has swollen slightly, and with the socks you actually work in: a composite toe cap does not give, and pressure across the toes will not break in with wear. Who they are for The Millington is aimed at construction and installation crews, plant and machinery operators, warehouse and transport work, utilities and agriculture - anywhere you stand and walk all day, the ground is wet, and a dropped object or a nail underfoot is a real risk. Safety footwear remains the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries measured in months of recovery. Technical specifications ModelDeWalt Millington Brown Order numberDWF50202-104-11 TypeRigger boot, no laces SizeEU 45 (UK 11) ClassificationS3 WR HRO SRA StandardEN ISO 20345:2011 Toe capComposite, non-metallic Underfoot protectionNon-metallic anti-penetration midsole Metal contentNone - 100% non-metallic construction UpperBrown nubuck with anti-scuff toe guard LiningWaterproof and breathable OutsoleDual-density PU/rubber Outsole heat resistanceContact heat to 300 °C (HRO) InsolePU comfort insole ColourBrown Questions and Answers What size are these boots? Order number DWF50202-104-11 corresponds to UK 11, which is EU 45. The number after the final hyphen is the UK size; add 34 to get the European size. What does the S3 WR HRO classification mean? S3 denotes safety footwear with a toe cap, an anti-penetration midsole, antistatic properties, energy absorption in the heel and a water-resistant upper. WR adds a whole-boot water resistance rating, and HRO means the outsole is tested against contact heat up to 300 °C. Is there any metal in the construction? No. The toe cap is composite and the midsole is non-metallic, so the boot is 100% non-metallic. That makes it lighter than its steel equivalent, stops cold conducting through to your toes, and means it will not trigger metal detectors. What is a rigger boot and how is it different? A rigger is a laceless boot with a tall shaft and two pull-on loops. The advantages are ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 41 (UK 7), DWF50140-133-7 DeWalt Newark Brown Buffalo (order number DWF50140-133-7) is protective work footwear with a mid cut profile in EU size 41, corresponding to UK 7. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 7 is EU 41. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-7 SizeEU 41 (UK 7) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-7 corresponds to UK size 7, that is EU 41. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 42 (UK 8), DWF50140-133-8 DeWalt Newark Brown Buffalo (order number DWF50140-133-8) is protective work footwear with a mid cut profile in EU size 42, corresponding to UK 8. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 8 is EU 42. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-8 SizeEU 42 (UK 8) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-8 corresponds to UK size 8, that is EU 42. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 44 (UK 10), DWF50140-133-10 DeWalt Newark Brown Buffalo (order number DWF50140-133-10) is protective work footwear with a mid cut profile in EU size 44, corresponding to UK 10. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 10 is EU 44. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-10 SizeEU 44 (UK 10) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-10 corresponds to UK size 10, that is EU 44. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

DeWalt Newark Brown Buffalo Safety Footwear, Size 45 (UK 11), DWF50140-133-11 DeWalt Newark Brown Buffalo (order number DWF50140-133-11) is protective work footwear with a mid cut profile in EU size 45, corresponding to UK 11. It is classified S3 WR SRA to EN ISO 20345. Toe and underfoot protection The footwear has a steel toe cap rated to 200 J and steel midsole plate. The plate covers the whole footbed and guards against penetration when stepping on a nail or rebar - the most common site accident after a fall from height. Upper and waterproofing The upper is waterproof buffalo leather with a Hydroguard membrane. The membrane works both ways: it keeps water out while letting perspiration vapour escape, so the foot does not get damp from inside. That is what separates a genuinely waterproof boot from a merely treated one, where the foot soaks in its own moisture after a few hours. Sole The sole is an injection-moulded PU/TPU outsole. The marking in the classification states the tested slip resistance - a figure that matters directly on wet concrete, steel ladders and spilled oil. Style and fit The model uses conventional lacing and a hiker profile with a reinforced heel for ankle support. A reinforced rand around the toe protects the upper from abrasion when kneeling and working close to rough surfaces. Choosing a size The order number ends in the UK size, and the European size is that plus 34 - UK 11 is EU 45. With safety footwear it is worth trying on in the afternoon, when the foot is slightly swollen, and in the socks you will actually work in: the toe cap is rigid and a tight fit will not break in with wear. Who they are for The footwear is aimed at construction and installation crews, warehouse and production staff, transport and logistics - anywhere you stand and walk all day and where a dropped object or a nail underfoot is a real risk. Safety footwear is also the cheapest piece of personal protective equipment relative to what it prevents: crushed toes and puncture wounds are injuries with months of recovery. Technical specifications ModelDeWalt Newark Brown Buffalo Order numberDWF50140-133-11 SizeEU 45 (UK 11) ClassificationS3 WR SRA StandardEN ISO 20345 Profilemid cut Toe capsteel toe cap rated to 200 J Underfoot protectionsteel midsole plate Upperwaterproof buffalo leather with a Hydroguard membrane Soleinjection-moulded PU/TPU outsole FasteningConventional laces WaterproofYes, with membrane Questions and Answers What size is this footwear? Order number DWF50140-133-11 corresponds to UK size 11, that is EU 45. The figure after the last hyphen in the number is the UK size; the European size is that plus 34. What does the S3 WR SRA classification mean? S3 denotes footwear with a toe cap, underfoot penetration resistance, antistatic properties, heel energy absorption and a water-resistant upper. WR is an additional degree of water resistance, and SRA/SRC the tested slip resistance. Is there metal in the construction? Yes - a steel toe cap rated to 200 J and a steel midsole plate. Steel gives maximum protection but weighs more than composite and conducts cold. If you need metal-free footwear, look for a model with a composite toe cap. Are they waterproof? Yes, the upper carries a waterproof membrane that keeps water out while letting perspiration vapour escape. That does not mean the boot can be submerged - water above the top of the tongue will get in over the edge. Are they suitable for all-day wear? Yes, that is what they are built for. With safety footwear it matters not to lace too tightly - the toe cap is rigid and squeezed toes have nowhere to go over a working day. How should the footwear be cared for? Let leather dry, brush the mud off, then treat with a proofer that does not block the membrane - ordinary wax pastes do, and the boot stops breathing. Never dry them on a radiator or by a stove: rapid drying shrinks the leather and separates the sole. How do they differ from ordinary work shoes? Safety footwear is tested to EN ISO 20345 - a 200 J impact on the toe cap, slip resistance, antistatic properties and, depending on class, penetration and water resistance. An ordinary work shoe may be tough, but it guarantees none of those figures. ..

Dewalt DWC52-001-XL T-shirtDescription: The Dewalt Oxside Tee Black is made of 65% polyester and 35% cotton, ensuring high durability and easy care thanks to the breathable fabric. It features a dark, reflective logo on the chest. Technical specifications:Size: XL Material: 65% polyester/35% cottonColor: black..

DEWALT DWC125-013-XL Collared T-ShirtDescription: The DEWALT PWS Polo Shirt Black is made of polyester, ensuring durability and reduced wear. It features gray trim on the sleeves and is easy to care for. Technical specifications:Size: XL Material: polyesterColor: gray/black..

DeWalt Rutland PWS Polo Shirt, Black/Grey, Size L, DWC125-013 DeWalt DWC125-013 is a work polo shirt from the Rutland line in black/grey, size L. It is made entirely from PWS polyester - a fabric that actively moves moisture away from the skin. What PWS is PWS (Performance Wicking System) is DeWalt's system for moving sweat away. The principle is simple but it is what separates a work shirt from an ordinary one: polyester fibres do not absorb moisture into themselves, they carry it along their surface to the outside, where it evaporates. The result is a shirt that dries fast and does not stick to your back. That is exactly why there is no cotton here. A cotton tee soaks up sweat and holds it - pleasant for the first hour, wet and cold by the third. For physical work outdoors that is uncomfortable, and on a cold day it is dangerous. Mesh panels There are mesh inserts down the sides and sleeves. They sit exactly where the body runs hottest and where nothing bears on the fabric - the shoulders and back stay solid cloth because of rucksack and belt, and the ventilation runs down the flanks. Reflective strips Each sleeve carries a reflective strip. That does not make the shirt high-visibility clothing to EN ISO 20471 - it has neither the fluorescent background nor the area the standard requires. The strips are extra visibility in poor light: a car park, a garage, work at dusk. Useful, but no substitute for a hi-vis vest on the road. Cut The fit is relaxed, the seams are flatlock, and the hem has side slits. A flatlock seam has no ridge to chafe as you move - in a shirt worn under a tool belt, that is a practical difference. The side slits let the shirt stay put instead of riding up when you bend. The front has a collar and a short button placket. Care Wash up to 40 °C. As with any technical fabric, do not use fabric softener - it blocks the fibres and removes exactly the property you paid for. Technical specifications ManufacturerDeWalt Article numberDWC125-013 ModelRutland PWS TypeWork polo shirt, short sleeve SizeL ColourBlack/grey Material100% PWS polyester VentilationMesh panels on sides and sleeves VisibilityReflective strip on each sleeve SeamsFlatlock FitRelaxed, with side hem slits FrontCollar with button placket WashingUp to 40 °C Questions and Answers What does PWS mean? Performance Wicking System - DeWalt's system for moving sweat away. Polyester fibres do not absorb the moisture but carry it along their surface to the outside, where it evaporates. Why is there no cotton in it? Because cotton soaks up sweat and holds it. Pleasant for the first hour, wet and cold by the third - uncomfortable for physical work outdoors and dangerous on a cold day. Is it high-visibility clothing? No. The reflective sleeve strips give extra visibility in poor light, but the shirt lacks the fluorescent background and the area EN ISO 20471 requires. On the road you still need a hi-vis vest. Where are the mesh panels? Down the sides and sleeves - exactly where the body runs hot and nothing bears on the fabric. Shoulders and back stay solid cloth because of rucksack and belt. Can it be washed with fabric softener? No. Softener blocks the fibres and removes the very wicking property the shirt is bought for. Wash up to 40 °C without softener. Why are the seams flatlock? A flatlock seam has no ridge to chafe as you move. Under a tool belt or a rucksack strap, that is a difference you feel over a full shift. Does it ride up when bending? The hem has side slits that let the shirt follow the movement rather than being pulled upward when you bend or raise your arms. ..

Disposable glovesFeatures: Nitrile gloves are made of 100% nitrile and are black in color. The gloves comply with and have been tested according to the highest international standards; they are highly resistant to oils and greases and also offer high protection against solvents, chemicals, and microbes. Soft and elastic, they are easy to put on and take off and have good thermal conductivity, which prevents hands from sweating. They are suitable for all kinds of repair work, cleaning, the food industry, and more. They are latex- and powder-free and are not sterile...

DeWALT Concealer Safety Goggles DPG82-11DDescriptionThe DeWALT Concealer DPG82-11D are professional safety goggles designed to protect the eyes from flying debris, dust, and impact hazards in demanding work environments. The goggle-style design provides a secure fit and a wider area of protection compared to standard safety glasses. The goggles feature clear polycarbonate lenses with UV protection, ensuring excellent visibility and reliable eye protection for both indoor and outdoor applications. A soft sealing gasket enhances comfort during extended wear, while the adjustable elastic strap provides a secure and stable fit. They are suitable for construction, maintenance, industrial, workshop, and repair applications where dependable eye protection and clear vision are essential.Technical SpecificationsBrand: DeWALTModel: ConcealerType: Safety gogglesLens material: PolycarbonateLens color: ClearUV protection: YesImpact resistant: YesAdjustable elastic strap: YesSoft sealing gasket: YesApplication: Eye protection for construction, industrial, maintenance, and workshop usePackage Includes1 pc. DeWALT Concealer Safety Goggles DPG82-11D..

Size: 10 Length: 28 cm Material: neoprene Number of fingers: 5 Color: black / yellow Usage: reusable The DEWALT DPG21 work gloves are made of neoprene and feature 5 fingers. The design ensures maximum dexterity and comfort while working. There is a terry cloth patch on the top of the thumb for wiping sweat from the face. A soft neoprene wristband provides additional comfort and easy fastening. A reinforced, padded palm ensures superior comfort and durability. The wrist area is made of breathable spandex/lycra for maximum comfort, ventilation, and convenience. ToughThreadTM double-stitched seams for greater durability. DeWALT DPG21 work gloves with synthetic-padded leather palms and spandex backs. The foam pads reduce stress vibrations, resulting in higher vibration resistance, which improves control over tools and materials. DEWALT DPG21 gloves ..