Workwear - Page 6

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 37 Milwaukee FLEXTRED 1M110133 (article number 4932493702, EU size 37) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493702 SizeEU 37 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493702 corresponds to EU size 37. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 40 Milwaukee FLEXTRED 1M110133 (article number 4932493705, EU size 40) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493705 SizeEU 40 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493705 corresponds to EU size 40. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 43 Milwaukee FLEXTRED 1M110133 (article number 4932493708, EU size 43) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493708 SizeEU 43 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493708 corresponds to EU size 43. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 46 Milwaukee FLEXTRED 1M110133 (article number 4932493711, EU size 46) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493711 SizeEU 46 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493711 corresponds to EU size 46. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS 1M110133 Safety Footwear, Size 47 Milwaukee FLEXTRED 1M110133 (article number 4932493712, EU size 47) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is textile with reinforced nubuck panels. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS 1M110133 Article number4932493712 SizeEU 47 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Uppertextile with reinforced nubuck panels Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493712 corresponds to EU size 47. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS B1M110133 Safety Footwear, Size 40 Milwaukee FLEXTRED B1M110133 (article number 4932498097, EU size 40) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is water-repellent nubuck leather. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. BOA Fit system Instead of laces the footwear uses a BOA Fit system with a rotating dial. Tightening takes one turn and adjusts precisely, including with gloves on - no untying, no knots working loose through the day. Release is by pulling the dial out. On work where boots come off several times a day, the time saved adds up. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS B1M110133 Article number4932498097 SizeEU 40 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Upperwater-repellent nubuck leather Toe capNon-metallic Penetration resistanceNon-metallic insert FasteningBOA Fit system with a rotating dial CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932498097 corresponds to EU size 40. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. How do they fasten? Through the BOA Fit system - turning the dial tightens evenly along the whole length, and pulling it out releases at once. It works with gloves on, does not loosen through the day and needs no tying. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S1PS B1M110133 Safety Footwear, Size 41 Milwaukee FLEXTRED B1M110133 (article number 4932498098, EU size 41) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S1PS. The upper is water-repellent nubuck leather. What class S1PS means The footwear is antistatic, with heel energy absorption, fuel-oil resistant and with non-metallic penetration resistance. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. BOA Fit system Instead of laces the footwear uses a BOA Fit system with a rotating dial. Tightening takes one turn and adjusts precisely, including with gloves on - no untying, no knots working loose through the day. Release is by pulling the dial out. On work where boots come off several times a day, the time saved adds up. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S1PS B1M110133 Article number4932498098 SizeEU 41 StandardEN ISO 20345:2022 Protection classS1PS Profilemid cut (over the ankle) Upperwater-repellent nubuck leather Toe capNon-metallic Penetration resistanceNon-metallic insert FasteningBOA Fit system with a rotating dial CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932498098 corresponds to EU size 41. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S1PS classification mean? S1PS denotes antistatic footwear with a closed heel, energy absorption, fuel-oil resistance and non-metallic penetration resistance. It does not include water resistance - wet conditions call for class S3S. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. How do they fasten? Through the BOA Fit system - turning the dial tightens evenly along the whole length, and pulling it out releases at once. It works with gloves on, does not loosen through the day and needs no tying. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S 1M171311 Safety Footwear, Size 37 Milwaukee FLEXTRED 1M171311 (article number 4932493741, EU size 37) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck in beige. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S 1M171311 Article number4932493741 SizeEU 37 StandardEN ISO 20345:2022 Protection classS3S Profilemid cut (over the ankle) Upperwater-repellent nubuck in beige Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493741 corresponds to EU size 37. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S 1M171311 Safety Footwear, Size 40 Milwaukee FLEXTRED 1M171311 (article number 4932493744, EU size 40) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck in beige. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S 1M171311 Article number4932493744 SizeEU 40 StandardEN ISO 20345:2022 Protection classS3S Profilemid cut (over the ankle) Upperwater-repellent nubuck in beige Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493744 corresponds to EU size 40. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S 1M171311 Safety Footwear, Size 45 Milwaukee FLEXTRED 1M171311 (article number 4932493749, EU size 45) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck in beige. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. Laces with a pocket The footwear uses conventional laces with a stowaway lace pocket. The pocket tucks the lace ends under the tongue, so they do not trail, catch on ladders and scaffolding, or soak up mud. It is a small detail that saves trips on site. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S 1M171311 Article number4932493749 SizeEU 45 StandardEN ISO 20345:2022 Protection classS3S Profilemid cut (over the ankle) Upperwater-repellent nubuck in beige Toe capNon-metallic Penetration resistanceNon-metallic insert Fasteningconventional laces with a stowaway lace pocket CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932493749 corresponds to EU size 45. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. What is the lace pocket? A small pocket under the tongue that tucks the lace ends away. They then do not trail on the ground, catch on ladders and scaffolding or soak up water - a small but practical guard against tripping. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S B1L110133 Safety Footwear, Size 41 Milwaukee FLEXTRED B1L110133 (article number 4932498111, EU size 41) is protective work footwear with a low cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck leather. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. BOA Fit system Instead of laces the footwear uses a BOA Fit system with a rotating dial. Tightening takes one turn and adjusts precisely, including with gloves on - no untying, no knots working loose through the day. Release is by pulling the dial out. On work where boots come off several times a day, the time saved adds up. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S B1L110133 Article number4932498111 SizeEU 41 StandardEN ISO 20345:2022 Protection classS3S Profilelow cut (below the ankle) Upperwater-repellent nubuck leather Toe capNon-metallic Penetration resistanceNon-metallic insert FasteningBOA Fit system with a rotating dial CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932498111 corresponds to EU size 41. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. How do they fasten? Through the BOA Fit system - turning the dial tightens evenly along the whole length, and pulling it out releases at once. It works with gloves on, does not loosen through the day and needs no tying. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S B1L110133 Safety Footwear, Size 43 Milwaukee FLEXTRED B1L110133 (article number 4932498113, EU size 43) is protective work footwear with a low cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck leather. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. BOA Fit system Instead of laces the footwear uses a BOA Fit system with a rotating dial. Tightening takes one turn and adjusts precisely, including with gloves on - no untying, no knots working loose through the day. Release is by pulling the dial out. On work where boots come off several times a day, the time saved adds up. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S B1L110133 Article number4932498113 SizeEU 43 StandardEN ISO 20345:2022 Protection classS3S Profilelow cut (below the ankle) Upperwater-repellent nubuck leather Toe capNon-metallic Penetration resistanceNon-metallic insert FasteningBOA Fit system with a rotating dial CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932498113 corresponds to EU size 43. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. How do they fasten? Through the BOA Fit system - turning the dial tightens evenly along the whole length, and pulling it out releases at once. It works with gloves on, does not loosen through the day and needs no tying. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

Milwaukee FLEXTRED S3S B1M110133 Safety Footwear, Size 44 Milwaukee FLEXTRED B1M110133 (article number 4932498127, EU size 44) is protective work footwear with a mid cut profile, certified to EN ISO 20345:2022 in class S3S. The upper is water-repellent nubuck leather. What class S3S means The footwear is everything in class S1PS plus water resistance of the upper and better protection in wet conditions. Penetration resistance is non-metallic, which gives better underfoot flexibility and more even coverage than a steel plate, which leaves the edges unprotected. Entirely metal free Both the toe cap and the midsole protection are non-metallic. Besides the lower weight, that means the boots pass through metal detectors without being removed - significant in airports, courts, energy sites and controlled-access production. Going metal free also removes the cold bridge through which a steel toe chills the foot in winter. BOA Fit system Instead of laces the footwear uses a BOA Fit system with a rotating dial. Tightening takes one turn and adjusts precisely, including with gloves on - no untying, no knots working loose through the day. Release is by pulling the dial out. On work where boots come off several times a day, the time saved adds up. Heel technologies Three elements work together. ENERGY FOAM is a cushioning insert that returns part of the energy of each step - noticeable after a full day standing on concrete. ROLLCAGE is a stabilising frame that limits sideways roll of the heel on uneven ground. STEP-RELEASE is a tab at the back that lets the boot be levered off with the other foot, without bending down. Sole and ESD The sole carries the SR marking for slip resistance and FO for fuel and oil resistance - on contact with fuel it neither degrades nor softens. The footwear is ESD certified, meaning static electricity is discharged in a controlled way, a requirement when working with electronics and in atmospheres with combustible dust or vapour. Technical specifications ModelFLEXTRED S3S B1M110133 Article number4932498127 SizeEU 44 StandardEN ISO 20345:2022 Protection classS3S Profilemid cut (over the ankle) Upperwater-repellent nubuck leather Toe capNon-metallic Penetration resistanceNon-metallic insert FasteningBOA Fit system with a rotating dial CushioningENERGY FOAM in the heel StabiliserROLLCAGE RemovalSTEP-RELEASE heel SoleSR - slip resistant, FO - fuel resistant ESDYes, certified Questions and Answers What size is this footwear? Article number 4932498127 corresponds to EU size 44. Every size of the model has its own article number, so when ordering check the number rather than the model name alone. What does the S3S classification mean? S3S covers everything in S1PS - antistatic, energy absorption, fuel-oil resistance and non-metallic penetration resistance - and adds water resistance of the upper. It is the class for outdoor and wet work. Is there any metal in the construction? No. Both the toe cap and the midsole protection are non-metallic. The boots pass through metal detectors, weigh less than steel-toed equivalents and create no cold bridge to chill the foot in winter. How do they fasten? Through the BOA Fit system - turning the dial tightens evenly along the whole length, and pulling it out releases at once. It works with gloves on, does not loosen through the day and needs no tying. What is ENERGY FOAM for? It is a cushioning insert in the heel that absorbs the impact of each step and returns part of the energy. The difference is most noticeable after a full day on your feet on concrete or another hard surface. What does ESD certification mean? The footwear discharges accumulated static electricity to ground in a controlled way rather than allowing a sudden discharge. That is a requirement when handling electronic components and in atmospheres with combustible dust or vapour. Are they suitable for all-day wear? Yes, that is what they are built for. ENERGY FOAM in the heel, the ROLLCAGE stabiliser and the metal-free construction together give lower weight and less fatigue than conventional steel-toed boots. ..

MILWAUKEE 8/M Winter GlovesDescription:MILWAUKEE 4932479566 gloves are designed to provide maximum durability and comfort all day long. Meeting CE Category 2 requirements, they are ideal for winter conditions and are wind- and water-resistant. Winter insulation and a double acrylic lining keep your hands warm while working in cold conditions. The integrated SmartswipeTM Knuckle is designed to allow the use of tablets, smartphones, and touchscreens without removing gloves or smudging the screen with dirty fingertips. We'd also like to add that the breathable fabric and built-in terry cloth sweat pad ensure the gloves remain comfortable throughout the day. With palms and fingers. Technical specifications:Size: 8/MType: WinterQuantity: 1 pair..

MILWAUKEE 9/L Winter GlovesDescription: The MILWAUKEE 4932479567 gloves are designed to provide maximum durability and comfort all day long. Meeting CE Category 2 requirements, they are ideal for winter conditions and are wind- and water-resistant. Winter insulation and a double acrylic lining keep your hands warm while working in cold conditions. The integrated SmartswipeTM Knuckle is designed to allow the use of tablets, smartphones, and touchscreens without removing gloves or wiping dirty fingertips across the screen. We'd also like to add that the breathable fabric and built-in terry cloth sweat wiper ensure the gloves remain comfortable throughout the day. With palms and fingers. Technical specifications:Size: 9/LType: WinterQuantity: 1 pair..

MILWAUKEE 7/S Winter GlovesDescription:MILWAUKEE 4932479731 gloves are designed to provide maximum durability and comfort all day long. Meeting CE Category 2 requirements, they are ideal for winter conditions and are wind- and water-resistant. Winter insulation and a double acrylic lining keep your hands warm while working in cold conditions. The integrated SmartswipeTM Knuckle is designed to allow the use of tablets, smartphones, and touchscreens without removing the gloves or smudging the screen with dirty fingertips. We'd also like to add that the breathable fabric and built-in terry cloth sweat pad ensure the gloves remain comfortable throughout the day. With palms and fingers. Technical specifications:Size: 7/SType: WinterQuantity: 1 pair..

MILWAUKEE Winter Gloves 12/XXXLDescription:MILWAUKEE 4932480976 gloves are designed to provide maximum durability and comfort all day long. Meeting CE Category 2 requirements, they are ideal for winter conditions and are wind- and water-resistant. Winter insulation and a double acrylic lining keep your hands warm while working in cold conditions. The integrated SmartswipeTM Knuckle is designed to allow the use of tablets, smartphones, and touchscreens without removing gloves or smudging the screen with dirty fingertips. We'd also like to add that the breathable fabric and built-in terry cloth sweatband ensure the gloves stay comfortable all day long. With palms and fingers. Technical specifications:Size: 12/XXXLType: WinterQuantity: 1 pc..

Milwaukee Hi-Vis Cut Level E Gloves, Size 8/M, 4932479932 Milwaukee 4932479932 are cut level E work gloves in a high-visibility colour, size 8 (M). They are certified to EN 388:2016 with the code 4X43E and EN ISO 21420. The palm is polyurethane dipped. What level E means Under EN 388:2016 cut resistance is expressed as a letter from A to F, determined by the TDM method. E is the second-highest level - between 3,000 and 5,000 newtons of force needed to cut through the material. For comparison, an ordinary work glove is class A or B. The full code 4X43E reads: 4 - abrasion resistance (highest level), X - the rotating blade test not applicable, 4 - tear resistance (highest), 3 - puncture resistance, E - TDM cut resistance. What they are for Level E is the grade for handling materials that cut by their nature: sheet metal and steel section, glass, wire stripping and ducting. Exactly where an ordinary glove is sliced through by a single awkward movement. Thin, not thick The usual expectation is that a cut-resistant glove has to be thick. These are the opposite - light and thin, with a polyurethane-dipped palm. The protection comes from the yarn structure, not from bulk, which preserves the feel in the fingers. There is also reinforced nitrile coating between thumb and forefinger - the zone that wears through first when gripping. Hi-vis and SMARTSWIPE The fluorescent material gives visibility in poor light - in a shaft, behind a machine, in a load bay. Palm and fingertips carry SMARTSWIPE: they work on a touchscreen, so the phone or tablet is used without taking the glove off. On a level E glove that is not a trivial feature - every removal and refit is a moment without protection. Technical specifications ManufacturerMilwaukee Article number4932479932 TypeCut-resistant work gloves Size8 (M) Cut levelE (EN 388:2016) Full EN 388 code4X43E StandardsEN 388:2016, EN ISO 21420 Palm coatingPolyurethane dipped ReinforcementNitrile between thumb and forefinger VisibilityFluorescent hi-vis colour TouchscreenSMARTSWIPE - palm and fingertips Questions and Answers What does level E mean? Under EN 388:2016 cut resistance is a letter from A to F. E is the second-highest level - between 3,000 and 5,000 N of force to cut through. An ordinary work glove is class A or B. How is the code 4X43E read? 4 - abrasion (highest), X - rotating blade test not applicable, 4 - tear (highest), 3 - puncture, E - TDM cut resistance. Are they bulky? No - they are light and thin. The protection comes from the yarn structure rather than from bulk, so the feel in the fingers is preserved. Do they work on a touchscreen? Yes - palm and fingertips carry SMARTSWIPE. You use the phone without removing the glove, and on a level E glove every removal is a moment without protection. What work are they intended for? Materials that cut by their nature: sheet metal and steel section, glass, wire stripping, ducting - where an ordinary glove is sliced through by a single movement. What size are they? 8 on the European scale, which is M. Both markings are printed on the glove itself. Do they protect against an angle grinder? No. No glove stops a spinning disc or a chain. Cut levels describe sharp edges and static blades, not powered cutting tools. ..

Milwaukee 4933478978 Heated Work JacketDescription: The Milwaukee HJCAMO6-0 camouflage jacket with heating is designed to meet the needs of active users year-round in a variety of environments. Combining a unique blend of functionality and style, the REALTREE XTRATM Camo model ensures a perfect fit and comfort in any setting. The jacket features Quiet-Shel l fabric-a stretchy blend of 90% polyester and 10% spandex-which not only withstands harsh working conditions but also extends the jacket's lifespan by up to five times. Its water- and wind-resistant properties ensure protection even in the most extreme weather conditions. The heating system includes 5 heating zones and 3 heat settings-High, Medium, and Low-distributing active heat to the core of the body. This provides increased warmth and stimulates blood circulation, offering up to 8 hours of runtime with an M12TM 3.0Ah REDLITHIUMTM battery. The jacket is fully machine washable and dryable, making it easy to maintain and ensuring it stays clean. Ships without battery and charger! Technical specifications:Voltage: 12 VBattery type: Li-IonMaterial: 90% polyester and 10% spandexSize: MColor: CamouflageWeight: 2.120 kg..