Hand tools - Page 22

Rennsteig 385 060 Jointing Chisel, 250 x 60 x 13 mm Rennsteig 385 060 is a jointing chisel 250 mm long with a 60 mm blade. It is made of high-alloy tool steel, hardened throughout its section, and weighs 545 grams. Made in Germany. Hardened throughout This is what separates it from cheap chisels, where only the edge is hardened. On a Rennsteig the whole body is hardened so it carries the blow without loss - the hammer's energy goes into the material rather than into deforming the tool. The second consequence is that the edge can be reground many times without reaching a soft core. The safety impact head The striking end has a special safety impact head that will not splinter or mushroom under a hammer. A split head on an old chisel is the classic source of steel fragments flying towards the eyes - that is precisely the failure this construction removes. The flat-oval profile The body has a flat-oval section of 26 x 13 mm rather than a round one. A flat profile will not roll in the hand under a blow, and it lets the edge be held at a precise angle to the joint - working mortar, that angle decides whether the joint is cleared or the brick is broken out. What it is for The primary use is construction: raking out joints in brickwork, removing old mortar, forming chases. The 60 mm width is the compromise between speed and control - a wider blade covers ground faster but asks for a heavier blow. Standards and approval The tool meets or exceeds the requirements of current standards, DIN among them, and is GS-approved. The GS mark is an independent German safety assessment - on a struck tool that means the material and the head have both been tested. Polished or painted Rennsteig offers article 385 060 in two finishes: polished (385 060 0) and painted (385 060 1). The tool is the same and both carry the golden dip coating; only the surface treatment differs. The photograph shows the polished version. The same chisel is also made in 50, 70 and 80 mm widths. Technical specifications ManufacturerRennsteig Article385 060 0 TypeJointing chisel Length250 mm Blade width60 mm Dimensions250 x 60 x 13 mm ProfileFlat-oval, 26 x 13 mm MaterialHigh-alloy tool steel HardeningThroughout the section Impact headSafety head, resists splintering and deformation CoatingGolden dip-coated FinishPolished Weight545 g ApprovalGS EAN4049002001949 Other widths in the range50, 70 and 80 mm Questions and Answers What is the blade width? 60 mm, at an overall length of 250 mm. The range also covers 50, 70 and 80 mm. Is only the edge hardened? No - the whole body is hardened. That is why the edge can be reground many times. Can the head split? It has a special safety impact head built specifically against splintering and mushrooming. Why is the profile flat? The flat-oval 26 x 13 mm section will not roll in the hand and allows a precise angle to the joint. Polished or painted? Article 385 060 comes in both: 0 = polished, 1 = painted. The photograph shows the polished version. Is it approved? Yes - GS, and it meets current standards including DIN. How much does it weigh? 545 grams. ..

Knipex 28 71 280 Extended Point-Nose PliersDescription: Knipex 28 71 280 extended assembly pliers feature a length of 280 mm, a jaw thickness of 9 mm, and a tip width of 3 mm. Their slim and extra-long design makes them ideal for gripping, adjusting, and assembling in hard-to-reach areas. These pliers offer reliable gripping, holding, and guiding of small copper tubes, screws, cables, and other round parts. The milled grooves with smooth surfaces ensure precision and safety during use. The Knipex 28 71 280 needle-nose pliers are particularly suitable for work in the automotive and mechanical engineering sectors, where precision, control, and maneuverability are required when working with small and hard-to-reach components. With their high-quality design and durability, these pliers are a reliable tool for both professionals and hobbyists. Technical specifications:Jaw thickness: 9 mmTip width: 3 mmJaw length: 76.5 mmTip thickness: 2.5 mmHead width: 20 mmDimensions: 280 x 55 x 14 mmWeight: 235 ghttps://youtu.be/mRLksFp1PvA..

Knipex 87 01 150 Adjustable PliersDescription: Knipex 87 01 150 plumbing pliers offer a grip range of up to 30 mm with a diameter of up to 36 mm and feature 16 adjustment positions, allowing for flexibility when working with parts of various sizes. They are made of high-quality chrome-vanadium steel, which ensures the tool's strength and durability. One of the key advantages of these pliers is their self-locking functionality, which prevents the jaws from slipping on the workpiece during use. The jaws are equipped with high-hardness teeth that ensure a firm and secure grip on the workpiece. The hardness of the teeth is 61 HRC, which guarantees a long service life for the tool and its effectiveness when working with various materials and under different conditions. The pliers' handles are coated with a non-slip plastic coating, which provides greater comfort and control during use, especially during prolonged use. Technical specifications:Grip: 30 mm, Ø 36 mmAdjustment positions: 16Dimensions: 150 x 33 x 14 mmMaterial: chrome-vanadium steelStandard: DIN ISO 8976Weight: 0.145 kg..