Vermin - Page 9

DeWalt Impact Ready Drill Tap Set, M4-M10, 5 Pieces, DT50060-QZ DeWalt DT50060-QZ is a set of five drill taps in M4, M5, M6, M8 and M10, with a 1/4" hex shank made for an impact driver. Each tool is three in one: it drills the hole, cuts the thread and countersinks - in a single pass. Three operations in one tool The usual route to a tapped hole is three separate tools and three changes: a drill for the pilot hole, a tap for the thread and a countersink for the chamfer. On these tools the tip drills, the middle section taps, and the upper section countersinks and clears the burr. The gain is not only time: it also removes the pilot-hole diameter error - the most common cause of a snapped tap or a thread that will not hold. Why a 1/4" hex shank The shank is a 1/4" hex, so the tool goes straight into an impact driver or a bit holder. Traditional tapping with a hand wrench takes feel and time; an impact driver does the same job in seconds. The shank is Impact Ready - hardened to absorb the sharp impulses that break ordinary shanks. The tip The tip uses a speed geometry that penetrates the material quickly and does not walk across the surface on starting. With an impact driver that matters: the machine does not give a gentle start, and an ordinary drill point would skate sideways before it bit. Which materials The tools are intended for metal and plastics. Typical applications are threads in sheet steel, metal sections, brackets and cabinets, fixing hangers and cable routes - anywhere threads are cut on site rather than in a workshop. Choosing the size The set covers M4 to M10 - the range that takes in most installation work. The pitch is metric standard, right-hand thread. Material thickness matters: for a thread to carry load you need at least two or three turns engaged, so in thin sheet the larger sizes cut cleanly but carry nothing. Working with them Keep the tool perpendicular to the surface - misalignment is the main cause of breakage. Do not stop halfway: one continuous pass produces a cleaner thread than several stops. In thicker metal, use cutting lubricant - it lowers the temperature and multiplies the tool's life. Withdraw in reverse under power, without pulling. Technical specifications ManufacturerDeWalt Article numberDT50060-QZ TypeDrill taps, three in one Piece count5 SizesM4, M5, M6, M8, M10 Shank1/4" hex, Impact Ready FunctionsDrilling, tapping, countersinking ThreadMetric standard, right hand LengthApproximately 156 mm MaterialsMetal and plastics Questions and Answers Do I need to drill a pilot hole first? No. The tool is three in one: the tip drills, the middle section cuts the thread and the upper section countersinks. That also removes pilot-hole diameter error - the most common cause of a snapped tap. Which sizes are in the set? Five sizes: M4, M5, M6, M8 and M10 - the range that covers most installation work. The thread is metric standard, right hand. What machine are they used with? The shank is a 1/4" hex that goes straight into an impact driver or a bit holder. It is Impact Ready - hardened to absorb the sharp impulses that break ordinary shanks. Which materials do they work in? Metal and plastics. Typical uses: threads in sheet steel, metal sections, brackets and cabinets, fixing hangers and cable routes - anywhere threads are cut on site. Does material thickness matter? Yes. For a thread to carry load you need at least two or three turns engaged. In thin sheet the larger sizes cut cleanly but hold nothing - there you use a smaller size or a nut on the far side. How do I avoid breaking one? Keep the machine perpendicular - misalignment is the main cause of breakage. Do not stop halfway: one continuous pass gives a cleaner thread. In thicker metal use cutting lubricant. How is the tool withdrawn after tapping? In reverse under power, without pulling. Pulling it out by hand while it is still turning damages the first few turns of the thread - exactly the ones that carry the most load. ..

Hawera SoftCeramics Drill Bit, 12 mm, 90 mm, 265730DescriptionThe Hawera SoftCeramics 265730 is a specialized drill bit designed for drilling ceramic tiles, wall tiles, and other soft ceramic materials. Its specially engineered tip geometry ensures precise positioning and clean drilling while reducing the risk of slipping on smooth tile surfaces. With a diameter of 12 mm and a length of 90 mm, this drill bit is ideal for creating larger holes for pipe installations, fasteners, sanitary fittings, and other applications requiring accurate drilling in ceramic materials. For best results, it should be used without hammer action. The drill bit is suitable for professional installers, tilers, and DIY users who need a reliable solution for drilling ceramic materials.Technical Specifications Brand: Hawera Series: SoftCeramics Type: Ceramic drill bit Diameter: 12 mm Overall length: 90 mm Suitable for: Ceramic tiles and soft ceramics Operating mode: Non-hammer drilling Application: Installation and finishing work Package Includes 1 pc. Hawera SoftCeramics Drill Bit, 12 mm..

Hawera SoftCeramics Drill Bit, 5 mm, 70 mm, 265723DescriptionThe Hawera SoftCeramics 265723 is a specialized drill bit designed for drilling ceramic tiles, wall tiles, and other soft ceramic materials. Its specially designed tip geometry ensures precise drilling starts and reduces the risk of slipping on smooth tile surfaces. With a diameter of 5 mm and a length of 70 mm, the drill bit is ideal for installation and finishing tasks such as mounting wall plugs, fasteners, bathroom accessories, and other applications requiring accurate holes in ceramic materials. It is intended for use without hammer action to help prevent cracking and damage to tiles. Its compact size and durable construction make it suitable for both professional installers and DIY users.Technical Specifications Brand: Hawera Series: SoftCeramics Type: Ceramic drill bit Diameter: 5 mm Overall length: 70 mm Suitable for: Ceramic tiles and soft ceramics Operating mode: Non-hammer drilling Application: Installation and finishing work Package Includes 1 pc. Hawera SoftCeramics Drill Bit, 5 mm..

Makita Masonry Drill Bit D-05262, 6 x 150 mmDescriptionThe Makita D-05262 is a masonry drill bit with a cylindrical shank, designed for drilling into concrete, masonry, brick, and natural stone. With a 6 mm diameter and 150 mm overall length, it is ideal for accurate drilling in construction, installation, and renovation applications. The drill bit is designed for use with rotary and percussion drills equipped with a standard chuck for cylindrical shanks. Its durable construction and high-quality carbide tip provide efficient drilling performance and long service life. Suitable for both professional tradespeople and DIY users, it is a reliable accessory for drilling into mineral-based construction materials.Technical Specifications Brand: Makita Model: D-05262 Type: Masonry drill bit Diameter: 6 mm Overall length: 150 mm Shank: Cylindrical Application: Concrete, masonry, brick, and stone Compatibility: Rotary and hammer drills with standard chuck Package Includes 1 pc. Makita D-05262 Masonry Drill Bit..

Milwaukee Diamond Drill Bit Ø12 mm, 1/4" HEX, 4932498345DescriptionThe Milwaukee 4932498345 is a 12 mm diamond drill bit featuring a 1/4" HEX shank, designed for precise drilling in hard materials such as ceramic tiles, porcelain, porcelain stoneware, natural stone, and other hard surfaces. Its diamond-coated cutting edge delivers clean holes, excellent wear resistance, and long service life.The 1/4" HEX shank allows quick bit changes and is compatible with drill drivers, cordless drills, and impact drivers equipped with a suitable bit holder. It is an excellent choice for professional installers and tradespeople working with hard tile and stone materials.Technical Specifications Brand: Milwaukee Type: Diamond drill bit Diameter: 12 mm Shank: 1/4" HEX Cutting edge: Diamond coated Application: Ceramic, porcelain, porcelain stoneware, natural stone, and other hard materials Compatibility: Drill drivers, cordless drills, and tools with a 1/4" HEX holder Package Includes 1 pc. Milwaukee Ø12 mm Diamond Drill Bit..

Milwaukee Premium Hammer Drill Bit Set, 8 Pieces, 4932493882DescriptionThe Milwaukee Premium Hammer Drill Bit Set (4932493882) is a professional 8-piece masonry drill bit set designed for use with hammer drills when drilling into concrete, brick, masonry, natural stone, and other construction materials. The drill bits are manufactured from high-quality tool steel and feature carbide (HM) tips for excellent wear resistance and long service life. Their optimized tip geometry improves centering accuracy and enables faster, more efficient drilling. The set is supplied in a durable plastic storage case, keeping the drill bits organized and protected during storage and transportation.Technical Specifications Brand: Milwaukee Series: Premium Hammer Drill Type: Hammer drill bit set Number of pieces: 8 Material: Tool steel Tip: Carbide (HM) Shank: Straight shank Suitable for: Concrete Brick Masonry Natural stone Compatible with: Hammer drills Package Includes 8 x Milwaukee Premium Hammer Drill Bits Plastic storage case..

DEWALT has announced the launch of its XLRTM SDS Plus drill bits. The new range is designed for builders, electricians, plumbers, concrete product manufacturers, renovation and restoration contractors, glaziers, and general contractors for drilling holes in hard concrete, reinforced concrete, hard natural stone flooring, decorative panels, and blocks. Designed and manufactured in Germany, DEWALT XLR TM drill bits feature a head made entirely of carbide insert, utilizing a new two-stage brazing technology to bond the carbide insert to the drill bit body. Offering significantly increased durability and a long service life even under the most extreme operating conditions, DEWALT XLR TM drill bits with a head made entirely of carbide ensure greater reliability, a longer service life, and faster completion times for every application Manufacturer: DeWALT Length: 260.00 mm Working length: 200.00 mm Chuck: SDS plus Brand: XLR Application: for concrete Material: HM Outer diameter: 6.00 mm..

DEWALT has announced the launch of its XLRTM SDS Plus drill bits. The new range is designed for electricians, construction workers, plumbers, concrete product manufacturers, renovation and restoration contractors, glaziers, and general contractors for drilling holes in hard concrete, reinforced concrete, hard natural stone flooring, decorative panels, and blocks. Designed and manufactured in Germany, DEWALT XLR TM drill bits feature a head made entirely of carbide insert, utilizing a new two-stage brazing technology to bond the carbide insert to the drill bit body. Offering significantly increased durability and a long service life even under the most extreme operating conditions, the DEWALT XLR TM-with a head made entirely of carbide-provides the end user with greater reliability, a longer service life, and faster completion times for every application. Manufacturer: DeWALT Length: 210.00 mm Working length: 150.00 mm Chuck: SDS plus Brand: XLR Shank: 6.50 mm Application: for concrete Material: HM..

Irwin granite drill bits are designed for hammer drilling in very hard materials such as granite, concrete, and natural stone. They are 40% more durable than conventional masonry drill bits, thanks to their exceptionally hard, thicker, and stronger carbide tip. The rounded cutting edges also improve durability, resulting in up to 50% greater accuracy in hole size. This Irwin granite drill bit set contains 5 pieces in the following sizes: 4 mm, 5 mm, 6 mm, 8 mm, and 10 mm. Specifications Diameters: 4 mm, 5 mm, 6 mm, 8 mm, and 10 mm For hammer drilling in very hard materials such as granite, concrete, and natural stone 40% longer-lasting than conventional masonry drill bits With rounded cutting edges EAN: 5709131248187 Brand: Irwin Catalog number: 10501917..

Milwaukee HSS-G Combination Drill and Tap M6 x 57 mm, 4932498264DescriptionThe Milwaukee 4932498264 is a HSS-G combination drill and tap designed to drill and cut M6 threads in a single operation. Its combined design improves productivity by eliminating the need to switch between separate drill bits and taps. Manufactured from HSS-G (High Speed Steel - Ground), the tool provides excellent precision, wear resistance, and reliable performance in suitable metalworking applications. The compact M6 x 57 mm size makes it ideal for professional installation, maintenance, and fabrication work. The Milwaukee 4932498264 is an excellent choice for mechanics, installers, and metalworking professionals seeking an efficient drilling and tapping solution.Technical Specifications Brand: Milwaukee Type: Combination drill and tap Material: HSS-G Thread size: M6 Overall length: 57 mm Application: Drilling and thread cutting in one operation Package Includes 1 x Milwaukee HSS-G Combination Drill and Tap M6 x 57 mm..

BOSCH CYL-9 SoftCeramic Glass and Ceramic Drill Bit, 10 x 90 mm The BOSCH CYL-9 SoftCeramic drill bit, with a diameter of 10 mm and a length of 90 mm, is the standard choice for drilling in ceramic tiles. It is suitable for dry drilling without lubrication for convenient use. It features a simple, non-fluted design, particularly suitable for drilling in ceramic tiles. It offers high wear resistance and long-lasting performance when drilling holes in glass, ceramics, and various types of tile. Technical specifications:Brand: BOSCH;Diameter: 10 mm;Overall length: 90 mm;Shank: cylindrical shank;Application: Glass, ceramics, earthenware;Features: carbide tip;Quantity per package: 1 pc.;Weight: 0.040 kg...