Your Cart

Annular Cutter - Rotabroach, M2AL Raptor, 19 x 25 mm, RAP190

Annular Cutter - Rotabroach, M2AL Raptor, 19 x 25 mm, RAP190
Second hand
Technical specifications:
  • Manufacturer: Rotabroach
  • Range: M2AL Raptor
  • Article: RAP190
  • Diameter: 19 mm
  • Cutting depth: 25 mm
  • Material: M2AL (HSS with aluminium)
  • Shank: 19.05 mm (3/4 inch) Weldon
  • Max. material strength: 900 N/mm²
  • Pilot pin: Not included
  • Quantity: 1 piece
Annular Cutter - Rotabroach, M2AL Raptor, 19 x 25 mm, RAP190
29.00€
Ex Tax: 24.17€
  • Stock: In Stock
  • SKU:

    RAP190

Магазин Младост
0 бр.
Магазин Слатина
1 бр.
Склад
0 бр.
15 days right of return15 days right of return
Preview before paymentPreview before payment
Official distributorOfficial distributor
Secure online paymentSecure online payment

Rotabroach M2AL Raptor Annular Cutter 19 x 25 mm, RAP190

Rotabroach RAP190 is an annular cutter from the M2AL Raptor range, 19 mm in diameter with a 25 mm cutting depth. It carries a 19.05 mm (3/4 inch) Weldon shank with two flats - the standard that virtually every magnetic drill on the market accepts. Nineteen millimetres is one of the most used sizes in structural steel, because it clears an M16 bolt with normal assembly tolerance.

Why an annular cutter rather than a twist drill

An annular cutter removes only a ring of material and ejects the core in one piece instead of grinding the whole hole into swarf. At 19 mm in structural steel that means several times less cutting time, noticeably less load on the machine, and a hole with an accurate diameter and a clean wall, ready for a bolt or for tapping.

M2AL material

Raptor cutters are made from M2AL - high speed steel with an aluminium addition, heat-treated at high temperature. The addition raises the hardness of the cutting edges, which allows a higher cutting speed and extends tool life compared with a plain HSS cutter of the same class.

Tooth geometry

The Raptor range uses a tooth geometry developed by Rotabroach. It spreads the load across more cutting edges, so the cut runs more calmly, the chip is carried away in a controlled way and the wall of the hole comes out smoother. The cutter is rated for steel with a tensile strength up to 900 N/mm², which covers the sections, beams, sheet and plate used in structural steelwork, bridge building and general engineering.

Pilot pin and lubrication

The pilot pin is not included. Cutters with a 25 mm cutting depth take the short SRA25 pilot, which covers the whole 13-52 mm diameter range. The pilot centres the start of the cut and pushes the slug out at the end of the stroke. Generous lubrication with cutting paste or emulsion multiplies the life of the cutter - running dry is the most common cause of a broken tooth.

Technical specifications

Manufacturer Rotabroach (G&J Hall Tools)
Range M2AL Raptor
Model / article RAP190
Type Annular cutter
Diameter 19 mm
Cutting depth 25 mm
Material M2AL - high speed steel with aluminium, heat-treated
Shank 19.05 mm (3/4 inch) Weldon, two flats
Max. tensile strength of material up to 900 N/mm²
Suitable materials Structural and mild steel, aluminium, copper, brass
Pilot pin Not included - SRA25 for 25 mm depth
Pack quantity 1 piece

Questions and Answers

What hole does this cutter make?

A 19 mm hole up to 25 mm deep. The 25 mm depth is the standard for the RAP range - for thicker material the RAPL version of the same range cuts to 50 mm.

What shank does it have and will it fit my machine?

A 19.05 mm (3/4 inch) Weldon shank with two flats. This is the most widespread holder for magnetic drills, so the cutter fits machines from Rotabroach, ALFRA, BDS, EUROBOOR, HOUGEN, RUKO, UNIBOR, JEI and any other with the same holder.

Which pilot pin does it need, and is one included?

The pilot is not included. Cutters with a 25 mm cutting depth use the short SRA25 pilot, which serves diameters from 13 to 52 mm. Rotabroach recommends always cutting with a pilot fitted - it centres the start of the cut and ejects the slug at the end.

What material is it rated for?

Structural and mild steel with a tensile strength up to 900 N/mm², plus aluminium, copper and brass. It is not intended for hardened steels above that limit - those call for a cutter with carbide tips.

Can I use it in an ordinary drill?

No. The cutter needs a machine with a Weldon holder and rigid guidance - in practice a magnetic drill or a pillar drill with a suitable chuck. A hand-held drill cannot guide it accurately enough and the teeth break.

Does it need lubrication while cutting?

Yes, always. Cutting paste or emulsion carries heat and swarf away from the teeth. Running dry is the most common cause of premature dulling and of broken teeth on annular cutters.

What is the difference between M2AL and plain HSS?

M2AL is high speed steel with an aluminium addition, heat-treated at a higher temperature. It gives greater hardness at the cutting edges, which allows a higher cutting speed and extends the life of the tool.

Write a review

Note: HTML is not translated!
Rating
Bad Good

The delivery of each order is carried out on the territory of the Republic of Bulgaria with the courier company "ECONT EXPRESS" Ltd. and can be to their office or to an address specified by the client. The products are in their original packaging from the manufacturer. Each order includes the option: Preview and test before payment.

Free shipping

Toolsbox.bg offers its customers free shipping for all orders with total value over 76 € and weight up to 20 kg, excluding oversized products (ladders, scaffolding, generators)., to the Econt office for Bulgaria specified by the client!

Delivery time

The delivery time, to the address or to the office of the courier company, is from 1 to 3 (three) working days from the date on which the order was received and confirmed. If certain circumstances require a delay in the specified delivery times, we will notify you in a timely manner.

Deliveries are made every weekday from 9:00 to 18:00 and until 13:00 on Saturday. No deliveries are made on Sundays or public holidays.

The customer can track their shipment with their waybill number at: https://www.econt.com/services/track-shipment

Delivery cost

For all orders up to €76, over 20 kg or containing an oversized product (ladders, scaffolding, generators), a delivery fee is charged to the courier company. The delivery cost is formed depending on the dimensions and weight of the shipment, as well as your location.

We wish you a pleasant shopping!
The Toolsbox.bg team