Filter
Your Cart

Rechargeable batteries - Page 2

Batteries for cordless tools and machine..
Brand: Bosch Stock: In Stock
Bosch EXPERT Starter Set 3 x EXBA18V-40, 18V, 4.0Ah + GAL 12V/18V-80 Charger, 0615V0005X Set 0 615 V00 05X is a promotional starter pack from Bosch Professional with three EXPERT EXBA18V-40 batteries (18 V, 4.0 Ah) and one GAL 12V/18V-80 fast charger. The manufacturer describes it in exactly those words - a "promotional 18 V starter set with 3 batteries and a charger at a reduced package price". There is no machine in the box: this is the power side of the system, bought to feed a bare tool you already own or to replace worn-out packs. It ships in a cardboard box of 260 x 295 x 100 mm, EAN 4053423707502. Three identical batteries and one charger - no case, no tool, no accessories. The packs are marked HIGH POWER EXPERT 18V and 4Ah. The charger has a single bay and takes both 18 V and 12 V Bosch Professional packs, so the three batteries are charged one after another rather than at the same time. The EXPERT EXBA18V-40 battery Each of the three batteries is a lithium-ion pack of 18 V and 4.0 Ah built from 5 cells. One battery weighs 0.605 kg and measures 80 x 121 x 51 mm - the compact format that does not upset the balance of the tool in your hand. The cells are tabless: the two tabs of a conventional cell, which act as a bottleneck for the current, are replaced by a large number of parallel current paths. The result is lower internal resistance, less energy lost as heat and higher energy density. For the EXBA18V-40 Bosch states up to 2000 W maximum power and up to 2x the maximum power of the Professional GBA 18V 4.0Ah - both figures refer to instantaneous maximum power with a new, fully charged battery, measured in the manufacturer's internal test lab. The housing is reinforced and heat is managed by COOLPACK 2.0. Each pack carries a 5-LED indicator showing state of charge and remaining capacity, along with defect risk detection. The charging temperature range is extended to -10 °C to +55 °C battery temperature, but that applies when charging with the EXAL18V2-320 or EXAL18V-160, which are not in this set. The same goes for the shortest charging time Bosch quotes for this battery - 30 minutes with the EXAL18V2-320 or EXAL18V-160. The GAL 12V/18V-80 charger The charger works at 8 A charging current and covers 10.8 - 18 V, which is the whole range of 12 V and 18 V Bosch Professional batteries. With the packs from this set a full charge takes 38 minutes according to the manufacturer; for comparison, an 18 V 5.5 Ah pack charges in 46 minutes and a 12 V 4.0 Ah pack in 37 minutes. Cooling is active - Active Air Cooling 3.0 with a fan that cools the battery before, during and after charging. With three batteries in rotation that matters: a hot pack would otherwise wait to cool down before charging starts. The bay is a bay-in-bay design, with a smaller 12 V bay built into the 18 V one. The housing has two LED indicators and wall-mounting holes; dimensions 193 x 128 x 83 mm, weight 0.65 kg. Why three batteries rather than two Three batteries and one charger give you a working cycle: one pack in the tool, one in the charger, one standing by. With two packs the cycle only holds while the tool drains them more slowly than the charger refills them; as soon as a machine pulls 4.0 Ah in less than 38 minutes - an angle grinder or a circular saw under load, for instance - you wait. Three identical packs also cover two machines at once - a rotary hammer and a drill driver on one battery each, the third in the charger. Compatibility EXBA18V-40 batteries fit the tools of the Bosch Professional 18V System. Bosch states that the 18 V system has been compatible with all Bosch Professional tools and batteries of the same voltage class since 2008. The batteries and the charger are also part of AMPShare, the multi-brand battery alliance in which the manufacturer quotes access to more than 430 tools from Bosch Professional and partner brands. The charger adds the second platform: it also charges 12 V Bosch Professional packs, so one unit covers both systems. Who the set is for For someone who owns bare (battery-free) 18 V Bosch Professional machines and needs power for them. For a crew where one machine is passed from hand to hand. For replacing old packs when the machines are sound but the batteries no longer last half a day. Technical specifications Brand and rangeBosch Professional EXPERT Order number0 615 V00 05X EAN4053423707502 Number of batteries supplied3 pcs Battery modelEXPERT EXBA18V-40 (1 600 A03 6YW) Voltage18 V Battery capacity4.0 Ah Cell typeLi-ion, tabless, 5 cells, COOLPACK 2.0 Maximum power (battery)up to 2000 W (Bosch internal lab data, instantaneous power, new charged battery) Battery indicator5 LEDs - state of charge, remaining capacity, defect risk detection Charging temperature-10 °C to +55 °C (with EXAL18V2-320 or EXAL18V-160, not included) Battery dimensions80 x 121 x 51 mm Battery weight0.6..
-13%
299.00€ 343.20€
Ex Tax:249.17€
Add to Cart
Brand: Bosch Stock: In Stock
Bosch Set: 3 x GBA 18V 5.0Ah Battery + GAL 18V-40 Charger in L-BOXX 136, 0615990L3T Article 0615990L3T is a power set from the professional Bosch Professional 18 V system. It contains three lithium-ion GBA 18V 5.0 Ah batteries (order number 1 600 A00 2U5), one GAL 18V-40 charger (1 600 A01 9RJ) and an L-BOXX 136 case (1 600 A01 2G0). There is no power tool in the set - this is energy plus a case, for someone who already owns blue Bosch Professional 18 V machines or buys them in the SOLO version, without batteries. The arithmetic is simple: three 5.0 Ah packs at 18 V hold roughly 270 Wh in total (about 90 Wh per battery). That is a full day's supply for a drill driver, rotary hammer or angle grinder without walking back to a socket every half hour - while one battery works, the second charges and the third waits ready. The GBA 18V 5.0 Ah batteries GBA 18V 5.0 Ah is a lithium-ion pack with a voltage of 18.0 V and a capacity of 5.0 Ah. Bosch states 25% longer run time than an 18V 4.0 Ah battery from the same system. A single pack measures 74 x 114 x 56 mm and weighs 0.62 kg. The cells are protected by COOLPACK 1.0 - a design that moves heat from the inside of the pack to its surface. Heat is the main enemy of lithium cells, so better cooling means a longer service life and longer periods of continuous work under heavy load. The housing carries a battery status indicator that can be read without putting the pack into a tool. The GAL 18V-40 charger GAL 18V-40 is a compact charger with a charging current of 4 A and a working range of 14.4 - 18 V, so it also serves the older 14.4 V packs of the blue system. It weighs 0.55 kg. The charger has one bay - the batteries are charged one after another, not simultaneously. The housing has openings for wall mounting, which is a practical solution in a van, workshop or store room. The charging times stated by Bosch, to 80% and to 100%, are: GBA 18V 2.0 Ah - 24 / 35 min GBA 18V 3.0 Ah - 36 / 50 min GBA 18V 4.0 Ah - 48 / 65 min GBA 18V 5.0 Ah (the batteries in this set) - 60 / 70 min GBA 18V 6.0 Ah - 72 / 95 min For the three batteries in this set that means about 3 hours to reach 80% on all of them if they are charged in sequence, and about 3.5 hours to a full charge. The L-BOXX 136 case L-BOXX 136 is not a cardboard box but part of the Bosch storage and transport system. Its outer dimensions are 360 x 444 x 151 mm, the inner ones 302 x 386 x 114 mm, the weight is 1.9 kg and the material is ABS. It carries up to 100 kg on the top, up to 25 kg inside the box, and its tensile strength is 50 kg. The cases click onto one another and open without taking the whole stack apart. The latches lock securely and the additional front handle lets the case be carried close to the body. L-BOXX 136 works with the tool inserts and with the Sortimo vehicle system. Who this set is for The set makes sense in three situations: when buying a machine in the SOLO version (without battery and charger), when replacing worn-out packs that no longer last a shift, and in a crew of two or three people, where one battery per person is not enough and the tools stand idle. When the main machine is an angle grinder, rotary hammer or circular saw - a consumer that pulls current in bursts - three 5.0 Ah packs cover the working day more comfortably than two 4.0 Ah ones. Compatibility The GBA 18V 5.0 Ah batteries are compatible with all tools and chargers of the Bosch Professional 18 V system as well as with the AMPShare alliance. The GAL 18V-40 charger in turn is 100% compatible with all Bosch Professional 18 V batteries, including the ProCORE18V packs, and is also part of AMPShare. This is the blue professional system - the batteries do not fit the green Bosch tools for home use. Technical specifications BrandBosch Professional Set article number0615990L3T Set EAN3165140990868 Typebattery set + charger + case SystemBosch Professional 18 V, AMPShare Number of batteries3 Battery modelGBA 18V 5.0 Ah (1 600 A00 2U5) Battery voltage18.0 V Battery capacity5.0 Ah Cell typelithium-ion (Li-Ion) TechnologyCOOLPACK 1.0 Charge indicatoryes, on the battery housing Battery dimensions (W x L x H)74 x 114 x 56 mm Weight of one battery0.62 kg Charger modelGAL 18V-40 (1 600 A01 9RJ) Charging current4 A Battery charging voltage14.4 - 18 V Charger bays1 Charging time for 5.0 Ah (80% / 100%)60 / 70 min Wall mountingyes Charger weight0.55 kg CaseL-BOXX 136 (1 600 A01 2G0) Case outer dimensions360 x 444 x 151 mm Case inner dimensions302 x 386 x 114 mm Case materialABS Case load capacity100 kg on top, 25 kg inside Case weight1.9 kg Sum of the parts' weights4.31 kg Weight of the set with packaging≈ 4.67 kg Power tool in the setnot included Scope of delivery 3 x Bosch GBA 18V 5.0 Ah rechargeable battery, Li-Ion (1 600 A00 2U5) 1 x Bosch GAL 18V-40 Professional charger (1 600 A01 9RJ) 1 x Bosch L-BOXX 136 case (..
-20%
326.00€ 408.52€
Ex Tax:271.67€
Add to Cart
Brand: Dewalt Stock: In Stock
DeWALT DCB118X3 Charger and 3-Pack Battery Set, 18/54V, 9AhFeatures: DeWALT charger and 3-battery set with smart charging that adjusts power output based on the battery and reduces battery heat. These chargers fully charge the FLEXVOLT battery in about 60 minutes, can be wall-mounted for added convenience, and feature a flashing LED system that informs the operator of the charging cycle. The set includes:3 x DCB547 - 18/54V 9.0Ah, XR FLEXVOLT batteries;1 x DCB118 charger...
-24%
475.00€ 625.83€
Ex Tax:395.83€
Add to Cart
Brand: Einhell Stock: In Stock
Einhell 4512097 Battery and ChargerDescription: The Einhell Power X-Change 18 V / 2.5 Ah battery and charger set is part of the universal Power X-Change series, offering convenience and flexibility when working with all rechargeable devices compatible with this system. The batteries feature an ABS charge management system, ensuring maximum safety, optimal performance, and a long service life. Equipped with an LED display showing the charge status. The batteries feature high-quality Li-Ion cells with no memory effect and low self-discharge, ensuring consistent power. The housing design is protected against dust, corrosion, and mechanical damage, and includes a handle for easy removal. They are compatible with TWIN-PACK for use in heavy-duty applications requiring 36V. The chargers feature a compact, space-saving design and fast-charging technology, ensuring short charging times. They monitor the battery for optimal charging and have a built-in refresh mode, which allows for the reactivation of heavily discharged batteries. They feature a 6 -segment LED display to show current information and built-in mounting brackets for convenient wall mounting. Technical specifications:Voltage: 18 VCharger output voltage: 20 VSystem: Power X-ChangeBattery type: Li-ionBattery capacity: 2.5 AhCharging time: 58 minMax. power: 720 WKit includes:1 x18 V charger1 x 2.5 Ah rechargeable battery..
25.56€
Ex Tax:21.30€
Add to Cart
Brand: Einhell Stock: In Stock
Einhell 4512042 Battery and ChargerDescription: The Einhell Power X-Change 18 V / 4 Ah battery and charger set is part of the universal Power X-Change series, offering convenience and flexibility when working with all rechargeable devices compatible with this system. The battery features an ABS charge management system, ensuring maximum safety, optimal performance, and a long service life. Equipped with an LED display showing the charge status. The battery features high-quality Li-Ion cells with no memory effect and low self-discharge, ensuring consistent power. The housing design is protected against dust, corrosion, and mechanical damage, and includes a handle for easy removal. Compatible with TWIN-PACK for use in heavy-duty applications requiring 36V. The charger features a compact, space-saving design and fast-charging technology, ensuring short charging times. Battery monitoring for optimal charging and a built-in refresh mode that allows for the reactivation of heavily discharged batteries. Features a 6 -segment LED display for showing current information and built-in mounting brackets for convenient wall mounting. Technical specifications:Voltage: 18 VVoltage: 220-240 V ~ 50 HzSystem: Power X-ChangeBattery type: Li-ionBattery capacity: 4 AhCharging time: 80 minSet includes:1 x18 V charger1 x 4 Ah rechargeable battery..
40.90€
Ex Tax:34.08€
Add to Cart
Brand: Husqvarna Stock: In Stock
Husqvarna BLi200X Battery, 36 V, 5.2 Ah The Husqvarna BLi200X (article number 970448901) is a professional lithium-ion battery from the BLi-X 36 V system with a capacity of 5.2 Ah and around 187 Wh of energy. The "X" in the name denotes the professional build - with active cooling and reinforced construction. Active cooling This is the difference that justifies the higher price over ordinary packs. Under heavy load - cutting with a chainsaw, mowing long grass, sustained work with a brushcutter - the cells heat up and an ordinary battery reduces output to protect itself. Active cooling carries the heat away and lets the machine hold its power for longer instead of bogging down mid-job. Durability The battery is rated for up to 1500 charge cycles. Its construction is built for all weather conditions - dust, moisture and temperature swings, all normal for forestry and garden machinery. Power-to-weight is optimised: at 1.3 kg it is among the lighter batteries in its energy class. Charge indicator A four-LED indicator on the housing shows remaining charge at the push of a button. The check is made without inserting the pack into a machine or a charger - convenient when several batteries are in circulation. Who it is for The battery is aimed at forestry and landscaping firms, municipal services and owners of large properties running Husqvarna machinery daily. For such users a second and third battery is not a luxury but the condition for work not stopping - while one charges, the other is in the machine. The non-X packs in the range remain a sensible choice for occasional use in a garden. Compatibility The battery runs every machine on the Husqvarna BLi-X 36 V platform - chainsaws, brushcutters, trimmers, hedge trimmers, blowers, mowers and pole saws. One pack serves the whole fleet, removing the need for separate batteries per machine. Technical specifications ModelBLi200X Article number970448901 SystemHusqvarna BLi-X, 36 V TypeLithium-ion (Li-Ion) Voltage36 V Capacity5.2 Ah Energyaround 187 Wh Weight1.3 kg CoolingActive Charge cyclesup to 1500 Charge indicator4 LEDs ClassPRO range Applications Cordless chainsaws Brushcutters and grass trimmers Hedge trimmers Leaf blowers Pole saws Cordless mowers Questions and Answers Which machines is the battery compatible with? Every machine on the Husqvarna BLi-X 36 V platform - chainsaws, brushcutters, trimmers, hedge trimmers, blowers, mowers and pole saws. One pack serves the whole range of equipment in the system. What is the difference between BLi200 and BLi200X? The "X" marks the professional build with active cooling and reinforced construction. Under heavy sustained load that lets the machine hold its power for longer instead of reducing it because the cells are overheating. How many cycles does it last? Up to 1500 charge cycles in normal use. The real figure depends on load and on storage conditions - lithium-ion packs should not be left fully discharged for long periods or in direct sunlight. Why is the capacity quoted as either 5.0 or 5.2 Ah? It is the same battery. Husqvarna quotes 5.2 Ah and around 187 Wh for the European market, while in the US the same product is listed as 5 Ah and 180 Wh. The difference is in how it is measured, not a different pack. How do you check the remaining charge? With the four-LED indicator on the housing - press the button and the level shows immediately. The battery need not be inserted into a machine or charger, which is convenient with several packs in circulation through the working day. Can it be used in the rain? The construction is built for all weather conditions, including the moisture and dust normal in forestry and garden work. That does not mean the pack can be immersed or left out in the rain outside the machine - in storage it must be kept dry. How much does it weigh? 1.3 kg, which at around 187 Wh puts it among the lighter batteries in its class. On hand-held machines such as a chainsaw or brushcutter the pack's weight is felt directly, since it is carried all day. ..
-21%
229.00€ 290.00€
Ex Tax:190.83€
Add to Cart
Brand: Makita Stock: In Stock
Makita 191A24-4 Starter KitDescription: The Makita 191A24-4 battery and charger set includes high-quality products suitable for most Makita cordless tools. The DC18RC rapid charger is suitable for charging Li-Ion , Ni-Cd, and Ni-MH batteries. It features a faulty battery indicator, which will help you quickly identify the source of the problem, if any. The MAKITABL1830 Li-ion battery has a voltage of 18V and a capacity of 3.0Ah. Makita's modern Li-ion batteries are lighter, more efficient, have a higher capacity per unit weight, no memory effect, and negligible self-discharge rates. Technical Specifications: DC18RCVoltage: 230 ~ 50-60 Hz Charging voltage: 7.2 - 18 V Rated capacity: 1.5 - 5.0 Ah Battery type: Li-Ion / Ni-Cd / Ni-MHCharging time Li-Ion: 15 min (1.5 Ah), 22 min (3.0 Ah), 36 min (4.0 Ah), 45 min (5.0 Ah)Charging time for Makstar Ni-MH: 15-20 min (1.8 Ah), 22-30 min (3.1 Ah)Charging time Ni-Cd / Ni-MH: 30 min (1.3 Ah), 45 min (1.8-1.9 Ah), 60 min (2.5 Ah), 70 min (2.8 Ah)Dimensions (L x W x H): 185 x 155 x 87 mmWeight: 0.907 kg Ni-MH battery charging time: - 9.6V Ni-MH 1.7Ah - 20 min (B9017A) - 9.6V Ni-MH 1.8Ah - 20 min (BH9020/A) - 9.6V Ni-MH 3.1Ah - 30 min (BH9033/A) - 12V Ni-MH 1.8Ah - 15 min (BH1212/C) - 12V Ni-MH 3.1Ah - 22 min (BH1233/C) - 14.4V Ni-MH 1.8Ah - 15 min (BH1420) - 14.4V Ni-MH 2.5Ah - 20 min (BH1427) - 14.4V Ni-MH 3.1Ah - 22 min (BH1433) Li-Ion battery charging time: - 14.4V Li-Ion 1.3Ah - 15 min (BL1415) - 14.4V Li-Ion 1.5Ah - 15 min (BL1415N, BL1415NA) - 14.4V Li-Ion 3.0Ah - 22 min (BL1430, BL1430A, BL1430B) - 14.4V Li-Ion 4.0Ah - 36 min (BL1440) - 14.4V Li-Ion 5.0Ah - 45 min (BL1450) - 14.4V Li-Ion 6.0Ah - 55 min (BL1460A, BL1460B) - 18V Li-Ion 1.3Ah - 15 min (BL1815) - 18V Li-Ion 1.5Ah - 15 min (BL1815N) - 18V Li-Ion 2.0Ah - 24 min (BL1820, BL1820B) - 18V Li-Ion 3.0Ah - 22 min (BL1830, BL1830B) - 18V Li-Ion 4.0Ah - 36 min (BL1840, BL1840B) - 18V Li-Ion 5.0Ah - 45 min (BL1850, BL1850B) - 18V Li-Ion 6.0Ah - 55 min (BL1860B) Technical Specifications: BL1830Voltage: 18 VCapacity: 3.0 AhBattery type: Li-IonCharger: DC18RA, DC18RC, DC24SC, DC18SD, DC18SECharging time: 22, 22, 35, 60, 60 min Dimensions (L x W x H): 115 x 75 x 67 mmWeight: 0.641 kg ..
-6%
85.00€ 89.99€
Ex Tax:70.83€
Add to Cart
Brand: Makita Stock: In Stock
Makita 191J81-6 Battery and Charger Kit, 40V, 2x2.5 Ah, XGT The MAKITA 191J81-6 battery and charger set includes 2 BL4025 Li-ion batteries from the XGT series with a voltage of 40 V and a capacity of 2.5 Ah, a DC40RA rapid charger, and a Makpac 1 case. The average charging time for a 2.5 Ah battery is 28 minutes. 1. MAKITA BL4025 rechargeable battery, 40V, 2.5Ah, XGT, Li-IonVoltage: 40V;Battery type: Li-ion, XGT series;Battery capacity: 2.5 Ah;Charging time: 28 min.;Dimensions LxWxH: 395 x 295 x 110 mm;Weight: 0.750 kg2. MAKITA DC40RA Dual Fast Charger, 40VVoltage: 230 V ~ 50-60 Hz;Charging voltage: 40 V;Rated capacity: 2.5 Ah;Battery type: Li-Ion x 2;Charging time: 28 min (2.5 Ah);Dimensions (L x W x H): 156 x 210 x 84 mm;Weight: 1.0 kg.The set includes:MAKITA BL4025 rechargeable battery (2.5 Ah): 2 pcs.;MAKITA DC40RA dual fast charger: 1 pc.;MAKITA Makpac plastic storage and carrying case: 1 pc...
-17%
404.00€ 484.70€
Ex Tax:336.67€
Add to Cart
Brand: Makita Stock: In Stock
Makita has developed an exceptionally wide range of tools that use Li-ion batteries. In line with this, the company is also advancing its battery technology. Makita's modern Li-ion batteries are lighter, more efficient, have a higher capacity per unit weight, no memory effect, and negligible self-discharge rates. These batteries can be charged at any time, regardless of the remaining charge Manufacturer: Makita Warranty: 2 years after online registration Battery capacity: 4 Ah Type: for power tools Battery type: Li-Ion Brand: Makita Model: BL1041B Output voltage: 12 V Item type: Battery..
-19%
69.99€ 86.92€
Ex Tax:58.33€
Add to Cart
Brand: Makita Stock: In Stock
Makita 191L77-9 Starter KitDescription: The Makita 191L77-9 Starter Kit includes two 40 V rechargeable batteries with a capacity of 4.0 Ah , providing extended runtime and performance for all 40 V class tools. The kit also comes with a fast charger that charges a standard 40 V 4.0 Ah battery to 80% in just 31 minutes , ensuring minimal downtime. Compatible with all Makita tools and chargers from the 40V XGT system , this kit is the ideal solution for professionals who need high reliability and flexibility on the job site. Technical specifications:Voltage: 40 VCell type: Li-IonBattery capacity: 4.0 AhWeight (battery): 1 kgCharging voltage of the battery: 36-40 VCharging current: 6-12 ACharging time for a 5.0 Ah battery (80%/100%): 38/50 minCharging time for a 4.0 Ah battery (80%/100%): 31/45 minWeight (charger): 1 kg..
-45%
340.00€ 622.75€
Ex Tax:283.33€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee M12 B2 Battery, 12V, 2.0 Ah, 4932430064 Milwaukee M12 B2 (article number 4932430064) is a REDLITHIUM-ION lithium-ion battery rated 12 V and 2.0 Ah for the M12 system. It weighs just 0.2 kg and measures 97 x 57 x 68 mm. REDLINK - electronics inside the battery The pack is not simply a bundle of cells. It carries REDLINK electronics that communicate with the tool and monitor load from both ends at once. The practical consequence: on overload the system shuts down before damage occurs rather than after. It is also why other brands' batteries fitted through an adaptor perform poorly even when they physically fit - the communication is missing. Individual cell monitoring The electronics monitor each cell individually during charge and discharge. The reason is specific: in a pack of cells in series, the weakest determines the life of the whole pack. If it discharges deeper than the others it degrades, and in time the pack fails even though the remaining cells are sound. Individual monitoring balances the cells, and that is the main difference in longevity against cheap substitutes. Temperature management The temperature management system keeps the pack within its working range. Lithium cells are permanently damaged by charging below freezing and by running while overheated - the two most common causes of shortened life. A battery taken out of a cold vehicle in winter should be allowed to warm before charging. Deep-discharge protection The pack shuts itself off before it discharges below the safe threshold. That is why the tool stops abruptly instead of fading gradually - behaviour that surprises anyone used to nickel-cadmium packs. It is not a fault but exactly the protection that preserves the cells. 2.0 Ah - what it covers 2.0 Ah is the compromise the M12 system exists for: the pack is light and short and does not lengthen the grip, which is the main advantage of the 12-volt platform when working in confined spaces and overhead. On low-draw tools - a drill driver, a torch, a 1/4" impact wrench - it covers a working day. For heavier machines such as an angle grinder or a saw, a larger capacity is worth having. Compatibility The battery works with every tool in the Milwaukee M12 system and charges on any M12 charger. M18 packs do not fit - the two systems use different interfaces. The reverse is equally true: an M12 pack will not run an M18 tool. Technical specifications ManufacturerMilwaukee ModelM12 B2 Article number4932430064 TypeLithium-ion battery pack SystemM12 Voltage12 V Capacity2.0 Ah TechnologyREDLITHIUM-ION ElectronicsREDLINK, overload protection Cell monitoringIndividual, on charge and discharge Temperature managementYes Deep-discharge protectionYes Dimensions97 x 57 x 68 mm Weight0.2 kg Questions and Answers Which tools does it fit? Every tool in the Milwaukee M12 system, and it charges on any M12 charger. M18 packs do not fit - the two systems use different interfaces, and the reverse is equally true. Why does the tool stop abruptly instead of fading? That is the deep-discharge protection: the pack shuts itself off before the cells drop below the safe threshold. It is not a fault - that behaviour is exactly what extends the pack's life. Can I charge it straight after use? Let it come back to temperature. Lithium cells are damaged by charging while overheated, and equally by charging below freezing. Milwaukee chargers wait, but a pack taken out of a cold vehicle is best left indoors first. Does it have a memory effect? No. Lithium-ion packs have no memory effect and do not need fully discharging before a charge - that was a property of old nickel-cadmium packs. Top it up whenever you like. What does individual cell monitoring do? In a pack of cells in series, the weakest determines the life of the whole pack. Individual monitoring balances the cells on charge and discharge and prevents any one of them draining deeper than the rest. Is 2.0 Ah enough? On low-draw tools - a drill driver, a torch, a 1/4" impact wrench - it covers a working day. Heavier tools deserve a larger pack. In exchange 2.0 Ah is short and light and does not lengthen the grip, which is the main point of M12. Do other brands' batteries work with an adaptor? Even when they physically fit, the REDLINK communication between pack and tool is missing. Without it the overload protection does not work - and that is what shuts the system down before damage occurs, not after. ..
-48%
37.32€ 71.99€
Ex Tax:31.10€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee 4932492531 Dual Charger, M18DBSCDescription: The Milwaukee M18 DBSC fast charger provides up to 6 times faster charging to 80% compared to standard chargers, increasing productivity. It can charge the M18TM REDLITHIUMTM FORGETM 6.0 Ah battery to 80% in just 15 minutes. Adaptive charge distribution allows for simultaneous charging of multiple batteries to maximize productivity. With REDLINKTM intelligence, the charger communicates with the battery to ensure optimized charging speed and performance while charging two M18TM batteries at the same time. Compatible with all M18TM batteries and features easy wall mounting. The COOL-CYCLETM system provides an active cooling system for high-speed cooling. The active cooling function works with batteries that support COOL-CYCLETM. Technical specifications:Battery type: Li-ionSystem: M18TMBattery capacity: 2.0, 4.0, 5.0, 3.0, 5.5, 8.0, 12.0, 6.0 AhPower source: ACCharging ports: 2 x M18TMWall-mountable: yesCharging time for M18 3.0 Ah: 35 minCharging time for M18 5.0 Ah: 60 minCharging time for M18 12.0 Ah: 60 minWeight: 2.5 kghttps://youtu.be/6rnHjSnZ3jI?si=PKL_A5GjAaexSbkG..
-21%
255.65€ 323.99€
Ex Tax:213.04€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee Battery 4932492651Description:The Milwaukee M18FB12 rechargeable battery delivers up to 50% more power compared to 18V, 12Ah HIGH OUTPUT batteries, making it the most powerful in the range. REDLITHIUM FORGE technology delivers leading power, the fastest charging, and the longest runtime among all REDLITHIUM batteries. The COOL-CYCLE system actively cools the cells during operation and charging, preventing overheating and extending battery life. The improved housing is extremely durable and resistant to oils, solvents, and grease, making it suitable for harsh working conditions. The battery is designed for intensive applications, providing extended runtime for the most demanding tasks. The LED charge indicator remains clearly visible even in bright sunlight for easy level monitoring. The intelligent REDLINK system provides full overload protection and optimal performance through constant communication between the tool, battery, and charger. Fully compatible with all tools in the MILWAUKEE M18 platform.Technical Specifications:Voltage: 18 VCapacity: 12 AhBattery type: Li-IonCharger: M18 DBSC, M18 MDBSC, M12-18 SC, M12-18 FC, M18 DFC, M18 MPC6, M18 PC6, M12-18 C, M1418C6, M12-18 ACCharging time: 45, 45, 60, 130, 130, 130, 130, 250, 270, 285 minWeight: 1.51 kg..
-11%
320.00€ 359.99€
Ex Tax:266.67€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee Battery 4932492131Description:The Milwaukee M18 FB8 Forge rechargeable battery is a powerful and reliable power source for 18 V tools with a capacity of 8 Ah. It is equipped with an active cooling system that prevents overheating during operation and an extremely durable casing designed to withstand exposure to oils, solvents, and greases. The improved on-board charge indicator provides clear visibility even in bright sunlight, making it easier to plan your work. The battery is fully compatible with all tools in the M18TM series and is part of the REDLITHIUM FORGE line, known for its maximum power, fastest charging time, and long-lasting performance. This makes it the ideal choice for professionals who demand high performance and reliability.Technical Specifications:Voltage: 18 VType: Lithium-ionCapacity: 8 AhModel: M18 FB8System: M18Charging time: 45-190 minWeight: 1.08 kgCharging time with M12-18 SC charger: 45 minCharging time with M18 DBSC/MDBSC AC charger: 45 minCharging time with M12-18 FC charger: 87 minCharging time with M18 DFC charger: 87 minCharging time with M18 PC6/MPC6 AC charger: 87 minCharging time with M12-18 C charger: 167 minCharging time with M12-18 AC charger: 190 minCharging time with M1418C6 charger: 190 minhttps://youtu.be/grVf4jBgI3U?si=uaIDYsifib2z-JPa..
-30%
199.99€ 286.79€
Ex Tax:166.66€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee M18HB3 Rechargeable Battery, 18V, 3.0 Ah Li-ion The Milwaukee M18HB3 rechargeable battery features brand-new, revolutionary HIGH OUTPUTTM battery technology, delivering up to 50% more power for all M18TM tools compared to Milwaukee 's previous REDLITHIUMTM technology. The patented REDLINKTM intelligent system protects the battery from demanding job site conditions and ensures optimal performance. Up to 50% better cooling during operation compared to previous MilwaukeeTM REDLITHIUMTM technology, so users can use their tools for more demanding tasks and for longer than ever before.The battery's durable construction, featuring a metal casing with impact-resistant separators, prevents battery failure due to excessive vibration or drops. The M18 HB8's built-in battery charge indicator helps users maximize battery performance. Individual cell monitoring ensures optimal charging and discharging for maximum life. Compatible with all MilwaukeeTM M18 tools. Technical specifications:Voltage: 18 V;Battery type: Li-Ion;Battery capacity: 3.0 Ah;Quantity in set: 1 pc.;Weight: 0.700 kg...
-58%
80.00€ 191.00€
Ex Tax:66.67€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee MX FUEL REDLITHIUM CP203 Battery, 3.0 Ah The Milwaukee MXF CP203 (article number 4933471838) is a lithium-ion battery of 3.0 Ah for the professional MX FUEL platform. Unlike the usual cordless systems for hand tools, MX FUEL powers heavy equipment - breakers, concrete saws, vibrators, pumps and lighting towers - machinery that until recently ran on a petrol engine. Why MX FUEL instead of petrol The battery allows work with no exhaust fumes and no engine noise. That makes it usable where petrol machinery is prohibited or impractical - indoors, in shafts, trenches, tunnels, underground car parks and on night work in residential areas. It also removes the cost of fuel, oil mixing and engine servicing. REDLITHIUM and power management The cells are from Milwaukee's highest grade of lithium-ion technology. An electronic management system monitors load and cell temperature and protects the pack against overload, overheating and deep discharge. The result is steady output power right to the end of the charge rather than a gradual fade. Built for hard conditions The housing carries a thick rubber overmould that absorbs impact if dropped, and is built to withstand vibration, moisture and dust. The battery operates at temperatures down to -28 °C, which matters on winter construction and outdoor work. A built-in gauge shows remaining charge at the push of a button, and an integrated handle makes it easy to carry. Who it is for The battery is aimed at construction and demolition contractors, infrastructure maintenance and utility crews already running MX FUEL equipment who need a spare or additional pack. On high-draw machines a second battery is effectively essential to keep work going while the first one charges. Charging A full charge takes around 45 minutes on the MX FUEL chargers - the MXF C at 4.5 A, the MXF FC at 8.0 A and the MXF SC at 12.0 A. The pack is interchangeable across every machine on the platform, so one battery can serve different equipment through the working day. Technical specifications ModelMXF CP203 Article number4933471838 PlatformMilwaukee MX FUEL TypeLi-Ion REDLITHIUM Capacity3.0 Ah Voltage72 V Charge timeapprox. 45 minutes Operating temperaturedown to -28 °C Fuel gaugeYes, built in Protectionagainst overload, overheating and deep discharge ConstructionRubber overmould, impact and vibration resistant CarryingIntegrated handle Compatible chargers MXF C - standard charger, 4.5 A MXF FC - fast charger, 8.0 A MXF SC - super charger, 12.0 A Questions and Answers What is the difference between MX FUEL and M18? They are two separate platforms and their batteries are not interchangeable. M18 is the 18 V system for hand-held power tools, while MX FUEL runs at 72 V and is built for heavy construction equipment that would otherwise be driven by a petrol engine or mains power. Which machines does this battery run? Every machine in the MX FUEL system - breakers, concrete saws, submersible and vibrating equipment, pumps, lighting towers and other heavy plant. The battery is universal within the platform, so one pack can serve different machines through the working day. How long does it take to charge? Around 45 minutes for a full charge. The time is similar on all three chargers in the system - the MXF C at 4.5 A, MXF FC at 8.0 A and MXF SC at 12.0 A - because the higher-output chargers are intended for larger-capacity packs. Can it be used indoors? Yes, and that is one of the main reasons the platform exists. There are no exhaust fumes and no engine noise, which allows work in shafts, trenches, tunnels, underground car parks and inside buildings where petrol machinery is banned on safety grounds. How does it differ from the 6.0 Ah version? Only in capacity, and therefore in weight and runtime. The 6.0 Ah pack gives roughly twice the working time per charge but is also heavier. The 3.0 Ah CP203 is preferred where the machine is carried or repositioned often and every kilogram counts. Does it cope with cold? The battery is rated for operation down to -28 °C. That is a significant advantage on winter construction, where ordinary lithium-ion packs lose a considerable share of their capacity or refuse to deliver current at all. How do you check the remaining charge? With the built-in gauge on the housing - pressing the button lights LEDs showing the charge level. The check is made without inserting the pack into a machine or a charger, which is convenient when several batteries are in circulation on site. ..
586.80€
Ex Tax:489.00€
Add to Cart
Rechargeable batteries DeWALT DCB 184 x 2, 18V, 5,0Ah, Li-Ion, 2 pcs. Rechargeable batteries DeWALT DCB 184 x 2, 18V, 5,0Ah, Li-Ion, 2 pcs.
Second hand Label -27% Delivery in 1-3 days
Brand: Dewalt Stock: Delivery in 1-3 days
Two DEWALT DCB 184 x 2 XR lithium-ion batteries provide extended runtime and reliable power for fast completion of tasks. Lightweight and compact design for reduced fatigue and better access. No memory effect and virtually no self-discharge during storage, for maximum productivity. Technical SpecificationsCapacity - 5 AhVoltage - 18 VType: Li-IonDCB184 Warranty: 12 months..
-27%
130.00€ 177.66€
Ex Tax:108.33€
Add to Cart
Rechargeable batteries Makita BL1860B - 2 pcs, 18V, 6Ah Rechargeable batteries Makita BL1860B - 2 pcs, 18V, 6Ah
Second hand Label -58% Delivery in 1-3 days
Brand: Makita Stock: Delivery in 1-3 days
Makita 18V 6.0Ah Lithium-Ion Battery Charging time: 55 min. LED charge level indicator Compatible chargers: DC18RA, DC18RC, DC18RD, DC18SE, DC18SF Warranty: Business: 6 months Individuals: 12 months + 12 months after registration on the Makita website See more rechargeable batteries on our website...
-58%
170.00€ 408.52€
Ex Tax:141.67€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee M18 HB5 Rechargeable Battery, 18 V / 5.0 Ah, HIGH OUTPUT The M18 HB5 is a battery pack for the Milwaukee M18 system, rated 18 V with a capacity of 5.0 Ah. The cells are Li-ion. The pack itself carries the M18 REDLITHIUM HIGH OUTPUT marking along with the XC5 designation, and the manufacturer's article number is 4932499042. 18 V and 5.0 Ah within the M18 system Voltage decides which tools the pack will run; amp hours decide how long it runs them. 18 V is the single voltage across the whole M18 platform, so the battery drops straight into any tool in that range without an adapter. At 5.0 Ah it sits in the upper middle of the capacity line: enough for a drill driver, impact wrench or angle grinder through a working day, without the bulk of the largest packs. Charging times follow the charger Milwaukee quotes a separate charging time for each charger. The quickest is the M18 DBSC/MDBSC AC at 39 minutes. The M18 DFC, M18 PC6/MPC6 AC and M12-18 FC each take 59 minutes. The standard M12-18 AC, M12-18 C and M1418C6 need 100 minutes. What changes is the current the charger supplies, not the battery. Weight in the hand The pack weighs 0.785 kg. On a tool held up at arm's length - an angle grinder, a jigsaw, an impact wrench - that weight tells on the wrist after the first hour, which is why choosing a capacity is always a trade between runtime and fatigue. On bench or stand work the weight is irrelevant and the larger capacity is a straight gain. What is in the box This article ships on its own - the battery only, exactly as the manufacturer lists it. No charger, case or bag is included; order those separately if you do not already have them from the M18 system. 1 pc. Milwaukee M18 HB5 battery pack, 18 V / 5.0 Ah, Li-ion (supplied without a kitbox or bag and without a charger - per the manufacturer's specification: Standard equipment = "-", Supplied in = "No kitbox or bag supplied", No. of batteries supplied = 1) Technical specifications ManufacturerMilwaukee RangeM18 REDLITHIUM HIGH OUTPUT Article number4932499042 TypeRechargeable battery pack Battery typeLi-ion Voltage18 V Battery capacity5.0 Ah Weight0.785 kg No. of batteries supplied1 Charging time, M18 DBSC/MDBSC AC39 min Charging time, M18 DFC59 min Charging time, M18 PC6/MPC6 AC59 min Charging time, M12-18 FC59 min Charging time, M12-18 AC100 min Charging time, M12-18 C100 min Charging time, M1418C6100 min EAN (GTIN-13)4058546529116 Questions and Answers Which tools take this battery? Tools from the Milwaukee M18 system, which runs at 18 V. The pack slides straight on, with no adapter. What does 5.0 Ah mean in practice? Amp hours are the energy held in the pack, which is to say how long a tool keeps going on one charge. All else being equal, a 5.0 Ah pack lasts longer than a 4.0 Ah one and less than an 8.0 Ah one on the same tool. Is a charger included? No. The manufacturer lists Standard equipment as "-", meaning the battery alone. A charger is ordered separately. How long does it take to charge? It depends on the charger: 39 minutes on the M18 DBSC/MDBSC AC; 59 minutes on the M18 DFC, M18 PC6/MPC6 AC and M12-18 FC; 100 minutes on the M12-18 AC, M12-18 C and M1418C6. What do HIGH OUTPUT and XC5 on the pack mean? They are the markings Milwaukee prints on the housing. HIGH OUTPUT is the name of the range, and XC5 is the designation that corresponds to the 5.0 Ah capacity within it. How heavy is the pack? 0.785 kg according to Milwaukee. The weight matters most on tools that are held up for long stretches. Will it fit Milwaukee M12 tools? No. M12 is a separate 12 V system with a different mount. The confusion comes from chargers named M12-18, which serve both systems, but the pack itself is for M18 tools only. ..
-17%
144.00€ 174.10€
Ex Tax:120.00€
Add to Cart
Brand: Milwaukee Stock: In Stock
Milwaukee M18 HB5-CR Rechargeable Battery, 18 V / 5.0 Ah, HIGH OUTPUT M18 HB5-CR is a battery pack for the Milwaukee M18 system - a power source for the platform's tools, not a tool itself. Voltage is 18 V, capacity 5.0 Ah, the cells are Li-ion and the article number is 4932499330. The -CR suffix marks the chemical resistant housing. Which machines it fits Milwaukee describes the pack as compatible with all tools in the M18 range. 18 V is the single voltage of the platform, so the battery drops straight into drill drivers, impact wrenches, angle grinders and vacuums from the system, with no adapter. Packs from the M12 system and other brands' batteries do not fit. The -CR version and the label The housing is printed M18 REDLITHIUM HIGH OUTPUT with the marking XC5, the trade designation for 5.0 Ah. A shield symbol sits to the right of the text; it separates this resistant version from the plain M18 HB5 (4932499042), which has no shield. The two look alike in a photo, so the article number is the safest check. Charging Charging time depends on the charger, not on the battery. The quickest is M18 DBSC/MDBSC AC at 39 minutes. With M18 DFC, M18 PC6/MPC6 AC and M12-18 FC it takes 59 minutes; with the standard M12-18 AC, M12-18 C and M1418C6, 100 minutes. No charger is included. When to replace it and what to check A battery is a consumable: capacity falls with cycles and age, and the sign is a noticeably shorter run time on the same job. When swapping packs, check the contacts and rails for dirt and burn marks, the housing for cracks and swelling, and the tool's receptacle for play. A swollen pack, or one with liquid on the contacts, is not to be charged. What is in the delivery The article is supplied on its own, as the manufacturer's specification states. No case, bag or charger is included. 1 x Milwaukee M18 HB5-CR rechargeable battery, 18 V / 5.0 Ah, Li-ion (per the manufacturer: no. of batteries supplied = 1; no kitbox or bag supplied, and therefore no charger) Technical specifications ManufacturerMilwaukee RangeM18 REDLITHIUM HIGH OUTPUT Article number4932499330 DesignationM18 HB5-CR (label reads: HIGH OUTPUT XC5) TypeRechargeable battery pack Battery typeLi-ion Voltage18 V Battery capacity5.0 Ah Weight0.785 kg No. of batteries supplied1 Charging time39 min with M18 DBSC/MDBSC AC; 59 min with M18 DFC, M18 PC6/MPC6 AC and M12-18 FC; 100 min with M12-18 AC, M12-18 C and M1418C6 CompatibilityAll tools in the Milwaukee M18 range Supplied asBattery only - no kitbox, bag or charger EAN (GTIN-13)4058546564940 Questions and Answers Which machines take this battery? Tools from the Milwaukee M18 system, which runs on 18 V - the manufacturer describes the pack as compatible with all tools in the range. It fits directly, with no adapter. It does not fit the M12 system or tools from other brands. What does the -CR stand for? It marks the version with a chemical resistant housing. The electrical data are the same as on the plain M18 HB5: 18 V, 5.0 Ah and 0.785 kg. What differs is the housing and the article number, which here is 4932499330. Why does the photo say XC5 instead of HB5-CR? XC5 is the trade designation for 5.0 Ah and it is what gets printed on the housing, while HB5-CR is the catalogue name of article 4932499330. It is the same pack. The shield symbol to the right of the text marks the resistant version. Is a charger included? No. The battery is supplied on its own, with no kitbox and no bag, and therefore without a charger. An M18 or M12-18 charger is ordered separately. How long does it take to charge? Per the manufacturer: 39 minutes with M18 DBSC/MDBSC AC; 59 minutes with M18 DFC, M18 PC6/MPC6 AC and M12-18 FC; 100 minutes with M12-18 AC, M12-18 C and M1418C6. The difference comes from the charger, not from the battery. How do I know it is due for replacement? When the same job drains the pack noticeably faster than it used to and the pack heats up more often. A swollen housing, a crack or liquid on the contacts is reason to take the pack out of service rather than charge it. What packaging does it ship in? The Bulgarian, English and Czech Milwaukee catalogues state "no kitbox or bag supplied", while the Austrian one lists a carton. The transport packaging may therefore differ, but in none of the cases are a case, a bag or a charger included. ..
-21%
206.00€ 261.84€
Ex Tax:171.67€
Add to Cart
Showing 21 to 40 of 195 (10 Pages)
Product Filter