Impact bits - Page 2

MAKITA B-66874 1/4"-1/2" Impact Socket Adapter The Makita B-66874 impact-resistant adapter is part of a premium series of screwdriver bits featuring a black anti-corrosion coating to prevent rust. Technical Specifications:F-female reducer size: 1/4"; Male adapter size: 1/2"; Shank: hexagonal;Length: 50 mm;Material: CrV (chromium-vanadium); Coating: phosphated;For use with: impact wrench;Max. torque: Nm;Connection type: ball joint;Weight: 0.10 kg;..

Milwaukee SHOCKWAVE Impact Bit Torx T25, 25 mm, 4932500375 Milwaukee 4932500375 is an impact bit from the SHOCKWAVE Impact Duty range in Torx T25, 25 mm long. The fitting is a 1/4" hex and the pack contains 3 pieces per pack. The Torx T25 recess T25 is the most common Torx size of all - the standard on decking screws, Torx-drive plasterboard screws, furniture fittings and mid-range structural screws. If there is one Torx bit in the box, it is usually this. What SHOCK ZONE is An impact driver does not deliver torque smoothly - it delivers it in blows, hundreds of times a minute. Each blow is an abrupt spike in load, and that is what breaks ordinary bits: the energy reaches the tip and snaps it off. SHOCK ZONE is a section of the shank with a reduced diameter, designed to twist elastically. It absorbs the blow and returns it like a spring, instead of passing it to the tip. Together with a special heat treatment it gives the bit a property that sounds contradictory for hardened steel: it flexes rather than breaks. The 25 mm length 25 mm is the short "insert" standard. The bit goes into a magnetic holder or straight into the impact driver's chuck. The advantage of the short length is stability: the shorter the bit, the less runout at the tip and the more accurately it seats in the recess. Making them last Most bits do not wear out - they break from bad technique. Three rules cover almost everything: hold the machine square to the screw axis - angled load concentrates in one corner of the tip; release the trigger the moment the head seats - every further blow only fatigues the bit; and never work a chewed-out recess - there the bit spins in the void, heats up and wears out in minutes. Technical specifications ManufacturerMilwaukee Article number4932500375 RangeSHOCKWAVE Impact Duty RecessTorx T25 Length25 mm Fitting1/4" hex TechnologySHOCK ZONE geometry Quantity3 pieces For machinesImpact drivers and drill drivers Questions and Answers What recess does the bit have? Torx T25, 25 mm long, with a 1/4" hex fitting. What does SHOCK ZONE do? It is a reduced-diameter section of the shank that twists elastically and absorbs the blow like a spring instead of passing it to the tip. With the special heat treatment the bit flexes rather than breaks. Why does an impact driver need a special bit? Because an impact driver delivers torque in blows, hundreds of times a minute. Each blow is an abrupt load spike, and that is exactly what snaps the tip off an ordinary bit. Does it work in an ordinary drill driver? Yes - the fitting is a standard 1/4" hex. The bit runs in both types of machine; the impact rating simply is not fully used in a machine without impact. Why only 25 mm long? That is the short "insert" standard. The shorter the bit, the less runout at the tip and the more accurately it seats. For extra reach, use a magnetic holder. How do I stop breaking bits? Three rules: machine square to the screw axis, release the trigger as the head seats, and never work a chewed-out recess - there the bit spins in the void and wears out in minutes. Is a holder needed? Not necessarily - the bit goes straight into the impact driver chuck. A magnetic holder does, however, also hold the screw while you place it one-handed, which at height often decides the job. ..

Milwaukee SHOCKWAVE Impact Bit Torx T30, 25 mm, 4932500376 Milwaukee 4932500376 is an impact bit from the SHOCKWAVE Impact Duty range in Torx T30, 25 mm long. The fitting is a 1/4" hex and the pack contains 3 pieces per pack. The Torx T30 recess T30 sits between the mid and the large class. It appears on 6 mm structural timber screws, heavy door ironmongery and steel section - applications where T25 is already at its limit. What SHOCK ZONE is An impact driver does not deliver torque smoothly - it delivers it in blows, hundreds of times a minute. Each blow is an abrupt spike in load, and that is what breaks ordinary bits: the energy reaches the tip and snaps it off. SHOCK ZONE is a section of the shank with a reduced diameter, designed to twist elastically. It absorbs the blow and returns it like a spring, instead of passing it to the tip. Together with a special heat treatment it gives the bit a property that sounds contradictory for hardened steel: it flexes rather than breaks. The 25 mm length 25 mm is the short "insert" standard. The bit goes into a magnetic holder or straight into the impact driver's chuck. The advantage of the short length is stability: the shorter the bit, the less runout at the tip and the more accurately it seats in the recess. Making them last Most bits do not wear out - they break from bad technique. Three rules cover almost everything: hold the machine square to the screw axis - angled load concentrates in one corner of the tip; release the trigger the moment the head seats - every further blow only fatigues the bit; and never work a chewed-out recess - there the bit spins in the void, heats up and wears out in minutes. Technical specifications ManufacturerMilwaukee Article number4932500376 RangeSHOCKWAVE Impact Duty RecessTorx T30 Length25 mm Fitting1/4" hex TechnologySHOCK ZONE geometry Quantity3 pieces For machinesImpact drivers and drill drivers Questions and Answers What recess does the bit have? Torx T30, 25 mm long, with a 1/4" hex fitting. What does SHOCK ZONE do? It is a reduced-diameter section of the shank that twists elastically and absorbs the blow like a spring instead of passing it to the tip. With the special heat treatment the bit flexes rather than breaks. Why does an impact driver need a special bit? Because an impact driver delivers torque in blows, hundreds of times a minute. Each blow is an abrupt load spike, and that is exactly what snaps the tip off an ordinary bit. Does it work in an ordinary drill driver? Yes - the fitting is a standard 1/4" hex. The bit runs in both types of machine; the impact rating simply is not fully used in a machine without impact. Why only 25 mm long? That is the short "insert" standard. The shorter the bit, the less runout at the tip and the more accurately it seats. For extra reach, use a magnetic holder. How do I stop breaking bits? Three rules: machine square to the screw axis, release the trigger as the head seats, and never work a chewed-out recess - there the bit spins in the void and wears out in minutes. Is a holder needed? Not necessarily - the bit goes straight into the impact driver chuck. A magnetic holder does, however, also hold the screw while you place it one-handed, which at height often decides the job. ..

Milwaukee SHOCKWAVE Impact Bit Torx T40, 25 mm, 4932500377 Milwaukee 4932500377 is an impact bit from the SHOCKWAVE Impact Duty range in Torx T40, 25 mm long. The fitting is a 1/4" hex and the pack contains a single bit. The Torx T40 recess T40 is the size for large structural screws - timber joists, decking, coach screws and support fixings. Tightening torque there is high, and the six-lobe recess is the only one that takes it without chewing out. What SHOCK ZONE is An impact driver does not deliver torque smoothly - it delivers it in blows, hundreds of times a minute. Each blow is an abrupt spike in load, and that is what breaks ordinary bits: the energy reaches the tip and snaps it off. SHOCK ZONE is a section of the shank with a reduced diameter, designed to twist elastically. It absorbs the blow and returns it like a spring, instead of passing it to the tip. Together with a special heat treatment it gives the bit a property that sounds contradictory for hardened steel: it flexes rather than breaks. The 25 mm length 25 mm is the short "insert" standard. The bit goes into a magnetic holder or straight into the impact driver's chuck. The advantage of the short length is stability: the shorter the bit, the less runout at the tip and the more accurately it seats in the recess. Making them last Most bits do not wear out - they break from bad technique. Three rules cover almost everything: hold the machine square to the screw axis - angled load concentrates in one corner of the tip; release the trigger the moment the head seats - every further blow only fatigues the bit; and never work a chewed-out recess - there the bit spins in the void, heats up and wears out in minutes. Technical specifications ManufacturerMilwaukee Article number4932500377 RangeSHOCKWAVE Impact Duty RecessTorx T40 Length25 mm Fitting1/4" hex TechnologySHOCK ZONE geometry Quantity1 piece For machinesImpact drivers and drill drivers Questions and Answers What recess does the bit have? Torx T40, 25 mm long, with a 1/4" hex fitting. What does SHOCK ZONE do? It is a reduced-diameter section of the shank that twists elastically and absorbs the blow like a spring instead of passing it to the tip. With the special heat treatment the bit flexes rather than breaks. Why does an impact driver need a special bit? Because an impact driver delivers torque in blows, hundreds of times a minute. Each blow is an abrupt load spike, and that is exactly what snaps the tip off an ordinary bit. Does it work in an ordinary drill driver? Yes - the fitting is a standard 1/4" hex. The bit runs in both types of machine; the impact rating simply is not fully used in a machine without impact. Why only 25 mm long? That is the short "insert" standard. The shorter the bit, the less runout at the tip and the more accurately it seats. For extra reach, use a magnetic holder. How do I stop breaking bits? Three rules: machine square to the screw axis, release the trigger as the head seats, and never work a chewed-out recess - there the bit spins in the void and wears out in minutes. Is a holder needed? Not necessarily - the bit goes straight into the impact driver chuck. A magnetic holder does, however, also hold the screw while you place it one-handed, which at height often decides the job. ..

Milwaukee SHOCKWAVE Impact Bit Torx T7, 25 mm, 4932500369 Milwaukee 4932500369 is an impact bit from the SHOCKWAVE Impact Duty range in Torx T7, 25 mm long. The fitting is a 1/4" hex and the pack contains a single bit. The Torx T7 recess T7 is a miniature Torx size. It does not appear in construction but in electronics, appliances, power tools and precision mechanics - screws in housings, boards and covers. Impact rating may look excessive here, but it makes sense: the small recess is also the most fragile, and the Shockwave geometry protects precisely that. What SHOCK ZONE is An impact driver does not deliver torque smoothly - it delivers it in blows, hundreds of times a minute. Each blow is an abrupt spike in load, and that is what breaks ordinary bits: the energy reaches the tip and snaps it off. SHOCK ZONE is a section of the shank with a reduced diameter, designed to twist elastically. It absorbs the blow and returns it like a spring, instead of passing it to the tip. Together with a special heat treatment it gives the bit a property that sounds contradictory for hardened steel: it flexes rather than breaks. The 25 mm length 25 mm is the short "insert" standard. The bit goes into a magnetic holder or straight into the impact driver's chuck. The advantage of the short length is stability: the shorter the bit, the less runout at the tip and the more accurately it seats in the recess. Making them last Most bits do not wear out - they break from bad technique. Three rules cover almost everything: hold the machine square to the screw axis - angled load concentrates in one corner of the tip; release the trigger the moment the head seats - every further blow only fatigues the bit; and never work a chewed-out recess - there the bit spins in the void, heats up and wears out in minutes. Technical specifications ManufacturerMilwaukee Article number4932500369 RangeSHOCKWAVE Impact Duty RecessTorx T7 Length25 mm Fitting1/4" hex TechnologySHOCK ZONE geometry Quantity1 piece For machinesImpact drivers and drill drivers Questions and Answers What recess does the bit have? Torx T7, 25 mm long, with a 1/4" hex fitting. What does SHOCK ZONE do? It is a reduced-diameter section of the shank that twists elastically and absorbs the blow like a spring instead of passing it to the tip. With the special heat treatment the bit flexes rather than breaks. Why does an impact driver need a special bit? Because an impact driver delivers torque in blows, hundreds of times a minute. Each blow is an abrupt load spike, and that is exactly what snaps the tip off an ordinary bit. Does it work in an ordinary drill driver? Yes - the fitting is a standard 1/4" hex. The bit runs in both types of machine; the impact rating simply is not fully used in a machine without impact. Why only 25 mm long? That is the short "insert" standard. The shorter the bit, the less runout at the tip and the more accurately it seats. For extra reach, use a magnetic holder. How do I stop breaking bits? Three rules: machine square to the screw axis, release the trigger as the head seats, and never work a chewed-out recess - there the bit spins in the void and wears out in minutes. Is a holder needed? Not necessarily - the bit goes straight into the impact driver chuck. A magnetic holder does, however, also hold the screw while you place it one-handed, which at height often decides the job. ..