Your Cart

Bent Nose Pliers 45° - TopMaster, DIN 5743, with Side Cutter, 210146

Bent Nose Pliers 45° - TopMaster, DIN 5743, with Side Cutter, 210146
Second hand Label -18%
Technical specifications:
  • Manufacturer: TopMaster
  • Article number: 210146
  • Jaw angle: 45°
  • Standard: DIN 5743
  • Marking: GS
  • Cutter: Integrated, side
  • Handles: Two-component
  • Insulation: No
Categories: Hand tools , Pliers
Bent Nose Pliers 45° - TopMaster, DIN 5743, with Side Cutter, 210146
-18%
4.59€
5.62€
Ex Tax: 3.83€
  • Stock: In Stock
  • Brand: TopMaster
  • SKU:

    210146

Магазин Младост
1 бр.
Магазин Слатина
0 бр.
Склад
0 бр.
15 days right of return15 days right of return
Preview before paymentPreview before payment
Official distributorOfficial distributor
Secure online paymentSecure online payment

TopMaster Bent Nose Pliers 45°, DIN 5743, 210146

TopMaster 210146 are pliers with jaws bent at 45 degrees, made to DIN 5743 and carrying the GS tested-safety mark. They have an integrated side cutter and two-component handles.

Why the jaws are bent

The 45 degree bend solves one specific problem: the hand gets in the way. With straight jaws, reaching a part at the bottom of a box, behind a board or under a cover means the wrist has to go in with the pliers. With bent jaws the hand stays outside the opening and works at an angle - you can see what you are gripping and your palm does not cover it.

Where they are used

The usual places are consumer units, junction boxes, the insides of appliances, vehicle dashboards and cabinets of every kind. Bent nose pliers are also the standard tool for routing and dressing wires in tight runs, where straight pliers would bend the cable the wrong way.

DIN 5743

DIN 5743 defines the shape and dimensions of this type - half-round jaws with a cutting edge. In practice the mark means the geometry of the jaws and of the cutter follows a standard rather than the maker's judgement. The GS stamp beside it means tested safety by an independent body.

Jaws and cutter

The inner faces of the jaws are serrated - which holds round parts that a smooth face would let slip. Behind the joint sits the side cutter for wire, so no tool change is needed to trim the excess after gripping.

The handles

The handles are two-component - a hard base with a soft non-slip overmould. The shape includes a stop at the upper end so the fingers cannot slide forward into the joint under a hard squeeze.

One important note

These pliers are not VDE insulated and are not intended for work on live parts. The soft coating on the handles is for grip and comfort, not electrical insulation. Work on live circuits calls for pliers certified to VDE 1000 V.

Technical specifications

Manufacturer TopMaster
Article number 210146
Type Bent nose pliers
Jaw angle 45°
Standard DIN 5743
Marking GS - tested safety
Cutter Integrated, side
Jaw grip Serrated inner faces
Handles Two-component, with finger stop
Insulation No - not VDE certified

Questions and Answers

Why are the jaws bent at 45 degrees?

So the hand stays outside the opening when working at the bottom of a box, behind a board or under a cover - you can see what you grip and your palm does not cover it.

Is there a cutter?

Yes - an integrated side cutter behind the joint. Excess wire is trimmed without changing tools.

What does DIN 5743 mean?

The standard for half-round jaws with a cutting edge - the geometry of jaws and cutter follows a norm rather than the maker's judgement.

What does the GS mark mean?

Tested safety by an independent body - the pliers have passed assessment under the German GS scheme.

Are they insulated?

No. The soft coating is for grip, not electrical insulation. Live work calls for pliers certified to VDE 1000 V.

Do they hold round parts?

Yes - the inner faces of the jaws are serrated, which holds round parts that a smooth face would let slip.

Where are they used most?

Consumer units, junction boxes, the insides of appliances and vehicle dashboards - anywhere tight where straight pliers do not sit comfortably.

Write a review

Note: HTML is not translated!
Rating
Bad Good

The delivery of each order is carried out on the territory of the Republic of Bulgaria with the courier company "ECONT EXPRESS" Ltd. and can be to their office or to an address specified by the client. The products are in their original packaging from the manufacturer. Each order includes the option: Preview and test before payment.

Free shipping

Toolsbox.bg offers its customers free shipping for all orders with total value over 76 € and weight up to 20 kg, excluding oversized products (ladders, scaffolding, generators)., to the Econt office for Bulgaria specified by the client!

Delivery time

The delivery time, to the address or to the office of the courier company, is from 1 to 3 (three) working days from the date on which the order was received and confirmed. If certain circumstances require a delay in the specified delivery times, we will notify you in a timely manner.

Deliveries are made every weekday from 9:00 to 18:00 and until 13:00 on Saturday. No deliveries are made on Sundays or public holidays.

The customer can track their shipment with their waybill number at: https://www.econt.com/services/track-shipment

Delivery cost

For all orders up to €76, over 20 kg or containing an oversized product (ladders, scaffolding, generators), a delivery fee is charged to the courier company. The delivery cost is formed depending on the dimensions and weight of the shipment, as well as your location.

We wish you a pleasant shopping!
The Toolsbox.bg team